Hot Stamping Machine For Pvc Foam Skirtings
Introduction of Hot stamping machine for pvc foam skirtingsOnline Hot Stamping Machine(360°running) Part 1. Application:☆ We have two kinds of online hot stamping machines for small profiles,Website:, one thermo-stamping head can be adjusted with 180°, one tehrmo-stamping head can be adjusted with 360°. They are special designed for decorating various PVC/PS/WPC/ABS/PVC foaming small profiles within 100mm widths; Now it is special used to decorating imitation marble stone profiles;☆ Normally for PVC marble profiles, there have 5-9surfaces, so we always match 10sets of online hot stamping machine to get complete marble designs;☆ For PS picture frame, it also need match 5-10sets, some for embossing, some for hot stamping, that will depended on the designs.☆ It is installed on the extrusion line, before Haul-off machine and after calibration table;☆ The center height of machine is 1000mm per center height of extrusion line. Part 2. The technical parameter of machine:Max width of thermoprinting100mmThe speed of thermoprinting 1—10 m/min ( adjustable)Thickness of panels 5—100 mmTransmission power 25W*2=50Wheating power 2KW by ceramic heaterThe total power 2.05 KWPower source Single-phase, 220V, 50 HzTotal weight 280KgCenter height1000mmVisual sizes (L*W*H) 750 × 750× 2000 mmPart 3: Basic assembly of OTR1003.1) Transmitting unit① The whole machine adopts 50*50,80*60 square tube and Q235 steel plate to weld.② It adopts Q235 steel to make conveying wheel seat and adjust it by hand wheels;③ It adopts cast iron wrapped with nylon to make conveying wheel.④ It adopts nylon to control the width of board.3.2) The angle adjustment unit① It adopts Q235 steel plate to make base-plate, clipboard and joint-plank.② It adopts Q235 steel plate to make big circle wheel.③ It adopts 160 hand-wheel to adjust thermoprinting angle by worm wheel and worm.3.3) The head of stamping control unit① It adopts Q235 steel plate to make erect plank, plank of air cylinder; and 50*80 air cylinder to control the stamping head work back and forth.② It adopts ZL102 with the copper slipcover to make guide thimble, and 45 steel for guide pole.③ It adopts ZL102 to make slide seat, 45 steels for slide shaft and flat steel to make index plate.3.4) The stamping head unit① It adopts ZL102 to make base-plate of thermoprinting which connect between slide shaft and slide seat.② It adopts Q235 steel to make heating cover and 2kw ceramic heater for heating, the temperature is controlled by Temperature controller.It adopts 45 steels to make axle and seat of thermoprinting.③ It adopts ZL102 wrapped with anti high temperature silicon rubber to make stamping wheel.④ It adopts 25w gear speed-down motor to drive stamping roller by gears.3.5) Winding & unwinding unit① It adopts 45# steel to make shaft and Q235 to make joint plate.② It adopts organic glass to make clamp for clamping film and aluminum loop to make fixed components.③ It adopts 25w electronic timing gear speed-down motor to drive winding shaft by gears.④ It adopts Q235 to make joint plate and 45# light&round steel to make shaft of guiding film.3.6) Electric control unit① It adopts cold rolled steel to make electric container.② The electric components of equipment adopts famous brand in home market. Part 4. Flow chart of OTR100Part 5. Payment and Delivery time1) Delivery time: Approx. 45days from receipt of down payment.2) Payment: 30% advance payment with order by T/T;70% balance payment paid before shipment by T/T.3) Guarantee: the machine is under warranty for one year, but not including the artificial wrong operation.4) Assembling works: Machine can be installed and start up will be done by our technician at your workshop. This period will not exceed 5 days including the training of your 2 people. For this service a round trip airplane ticket (economy class) and accommodation& food expenses of our technician will be borne by you, and offer 100USD/day as technical subsidy for our technician.
Другие товары поставщика
Все товары поставщика
Похожие товары