Single chip liquid crystal touch impact testing machine

Get a quote：

Whats/App: +86 181 0160 0864

Web: gellowen.co.uk

Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.

Standards

(1)GB/T 18910.101-2021

(2)IEC 60068-2-75:2014

Main features

Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.

Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.

Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.

Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.

Performance parameters

1. Simple beam impact testing machine

- Impact speed: 2.9m/s

- Impact energy: 1/2/4/5J

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 230mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

2. Cantilever beam impact testing machine

- Impact speed: 3.5m/s

- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 335mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

Accessories

The machine typically comes with the following standard and optional accessories:

(1)Impact Hammer / Dart – Different weights or tip types for various test requirements.

(2)Specimen Clamps / Fixtures – Hold films, plastics, metals, or laminates securely in place.

(3)Base Plate / Anvil – Provides a stable impact surface; may have adjustable height.

(4)Single Chip Microcontroller & LCD Touch Screen – Main control unit for parameter setting and data display.

(5)Force / Impact Sensors – Measure impact energy, force, or displacement.

(6)Calibration Weights or Blocks – For periodic verification of sensor accuracy.

(7)Protective Safety Shield – Ensures operator safety during impact tests.

(8)Software / Data Output Interfaces – For result recording and exporting (CSV, PDF).

(9)Optional Accessories:

Different shaped impact tips (ball, cone, flat)

High-speed camera for visualizing impact

Temperature or environmental chamber for tests under special conditions

Другие товары поставщика

	Glove Thermal Insulation Tester	Get a quote： Whats/App: +86 181 0160 0864 The Glove Thermal Insulation Tester is a precision instrument designed to evaluate the thermal insulati...
	Slip Resistance Tester ASTM F2913	Introduction Slips and trips are the most common cause of major injuries at work and can happen almost anywhere-broken bones and other serious inj...
	AATCC KMS-M6 Washer, KMS-M6D Dryer	Get a quote: Whats/App: +86 181 0160 0864 The AATCC KMS-M6 Washer and KMS-M6D Dryer are precision textile testing instruments designed to simulat...
	Scratch Resistance Test machine	Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Scratch Resistance Test Machine is a precision testing instrument designed to ...
	Wool Shrinkage Tester	Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk Type wool fold shrinkage tester is a precision instrument to determine the length ...

Все товары поставщика

Похожие товары

	Mini Jewelry Laser Repair System – 60W to 400W Precision Welding	Продавец: Beijing JCZ Technology Co., Ltd	The Mini Jewelry Laser Welding Machineis an advanced mini laser welding system engineered for pre...
	Portable Backpack Laser Cleaning Machine – Lightweight, Efficient Rust & Paint Removal	Продавец: Beijing JCZ Technology Co., Ltd	TheHCP-M SeriesBackpack Laser Cleaning Machinefeatures a compact pulsed fiber laser system, desig...
	Suitcase Pulsed Laser Cleaning Machine | Ultra-Portable Handheld Fiber Laser Cleaner	Продавец: Beijing JCZ Technology Co., Ltd	The Suitcase Pulsed Laser Cleaning Machineis an ultra-portable, high-precision handheld fiber las...
	All-in-One Fiber Laser Marking and Engraving Machine – AIO A2 for Metal Glass Plastic	Продавец: Beijing JCZ Technology Co., Ltd	The EZCAD AIO-A2 is a compact,all-in-one fiber laser marking machineengineered for versatility an...
	Compact Intelligent Laser Marking Machine – Advanced Technology for High-Quality Marking	Продавец: Beijing JCZ Technology Co., Ltd	The ETF-M20/30 is a desktop fiber laser marking machinedesigned to provide exceptional marking ca...