Sand - Falling Testing Machine for Motorcycle Helmets

• 

Main Purposes

It is mainly used to test the abrasion - resistance of the lenses of helmet goggles and evaluate their ability to resist particle - induced damage.

Applicable Standard

ASTM D968-83

JG/T 133-2000

Instructions for use:

1. according to the standard requirements for the preparation of test plates and placed in (23 +-2) degrees Celsius, relative humidity (50 +-5) degrees Celsius conditions for 24 hours.

2. Calibrate the apparatus:

Pour a certain amount of sand into the funnel, check the sand stream falling from the lower end of the conduit, and calibrate the device with the bottom adjusting screw until the inner part of the sand beam falls exactly on the center of the sand stream when viewed from two positions of 90 degrees Celsius each other. Use the high and low adjusting nut to adjust the distance from the tube tube to the painted surface according to the ASTM standard, when measured in the vertical direction, the near point of 1 inch (25mm), the user needs to be adjusted according to the thickness of their own samples, factory machine pre-adjustment of 25mm. to the pouring of a certain volume amount of sand (to 2000 +-10ml is appropriate), and measure the outflow time, the outflow rate should be 21S- 23.5S within 2L. This speed comes from the ASTM standard, and with the international standard sand for the test, we measured the speed of 1 minute 7L or more.

3. do the test should pay attention to, after the end of the sand fall, the machine should be slightly tilted to make the lower funnel in the small square of excess sand poured out, in the re-insertion of the sand fall switch in order to avoid the sand fall switch can not be put in.

Main Technical Parameters:

Overall Dimension: 230mm×200mm×1500mm (L×W×H)

Catheter Length: 36 inches (914mm)

Catheter I.D.: 0.75 inches (19mm)

Hopper Volume: 3L

Machine Weight: 25KG

Другие товары поставщика

	Thermal cycle wet freezing testing machine	Standard IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval UL 1073: Standard for Safety for Enclo...
	Automatic Reaction Calorimeter	Product Features： 1. It offers three calorimetry methods: heat - flow, power - compensation, and reflux, allowing users to choose according to the...
	Masks Flame Retardant Tester	Standards: GB 19083, YY 0469, GB 2626, EN 149, ISO 9473, EN 14325 Applications: Mask Flame Retardant Tester is a special test instrument f...
	Tibial Tray Fatigue Testing Machine	Standard YY/T 0810 (China): Specifies fatigue testing protocols for tibial trays in total knee arthroplasty, focusing on support and protection ...
	Leather Rubbing Colorfastness Tester	Introduction In daily life, leather products, such as leather clothing, purses, leather shoes ,etc., produce friction with their own or human body...

Похожие товары

	KL‑016A Benchtop High‑precision pH Meter	Продавец: Келийлонг Электронные Акционерные Компании	Product Description: Large‑screen display with high resolution and precision for con...
	Large Naïve VHH Library	Продавец: AlpVHHs	Large Naïve VHH Library VHHare single-domain antibodies derived from the variable regions o...
	pH-2398 pH/EC/ORP/Temperature multi-parameter Water Quality Tester	Продавец: Коллирон электроникс лимитед	Feature Large display screen, capable of simultaneously measuring water quality pH, redox potent...
	ORP-2026S Waterproof Soil ORP and Temperature Meter	Продавец: Коллирон электроникс лимитед	范围 ORP -999～999mV Temp 0～50℃ 分辨率 ORP 1mV...
	TDS-2616 Waterproof EC/TDS/Temperature Meter	Продавец: Коллирон электроникс лимитед	Range EC ～19.9mS TDS Temp 0～50℃ R...