Sprocket

When we intend to change the machining process to PM, we need to consider 4 questions: 1.     The quantity is big enough to ensure the investment of mould is reasonable, because the machining maybe doesn’t need to make mould; 2.     Evaluate the structure and tolerance, to prove the feasibility, then offer necessary changes;3.     Evaluate the required physical properties, it should be in the limitation of PM process;4.     Calculate and see if the PM process is really cost-efficient than other technologies. Gennerally speaking, there are few parts which are totally meet all above 4 points, but anyhow, the successful decision of PM is the result of positive compromise and deeply technical conversation. The main classifications of gear:1.     Pinion gear2.     Ring gear3.     Duplicate gear4.     Sprocket5.     Pulley6.     Worm gear7.     Spline hub They are widely used in motor, enginee, gearbox, oil pump, water pump and other structure of transmission. Advantages of PM gear:Few waste of the material, formed directly by only one or two times of pressingHigh efficiency, stable quality levelLow material and production cost Weakness of PM gear in comparison with machining gear:Yield strength, breaking stength of the toothDensity 7.2 g/cm³Profile precision H6~H8Macrohardness 25-40 HRCMicrohardness 60 HRC Max The application of PM partsAutomobile:Enginee parts, crankshaft timing belt pulley, water pump pulley, oil pump pulley, driving and driven gear, driving and driven sprocket, cam, bearing cap, rocker arm, bushing, thrust plate, valve guide, inlet and exhaust valve seat.Transmission parts, gear hub and parts of various high and low speed synchronizer, clutch gear, cam and camshaft (*), sliding block, shift lever, axle sleeve, guide block, synchronous ring. Motorcycle:Driven gear and parts, sprocket, starter pawl, ratchet, star gear, duplicate gear, pinion gear, gear ring, variable gear, pushrod cam, shaft sleeve, sliding bearing, centring sleeve, driven disc, inlet and exhaust valve seat. Oil pump parts:Oil pum gear, gear hub, various rotors, inner rotor and outer rotor, gerotor, cam ring.   



Send product request

To: DEWIN GROUP LIMITED
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

Ring Gear
Ring Gear When we intend to change the machining process to PM, we need to consider 4 questions: 1.     The quantity is big enough to ensure the investment o...
Sintered CuFe Bearing
Sintered CuFe Bearing Sintered bearing, also named oil impregnated bearing, is made by powder metallurgy technology, which is pressed by the mould and do sintering, coin...
Oil Pump Stator
Oil Pump Stator  Brief IntroductionOil pump stator is a basic component of oil pump, which co-work with the inner rotor or gear.We manufactured it by sintering (Po...
Sintered Copper Bearing
Sintered Copper Bearing Sintered bearing, also named oil impregnated bearing, is made by powder metallurgy technology, which is pressed by the mould and do sintering, coin...
Spline Coupling
Spline Coupling Spline Coupling,Website:http://www.dewin-powdermetallurgy.com,Air Compressor Parts
All supplier products

Same products

Water Pump 17400-73010
Water Pump 17400-73010 Seller: Ningbo Motor Industrial Co.,ltd. Water Pump 17400-73010 Water-Pump-17400-73010 Application Summary:SUZUKI   Product Description ...
Clutch Slave Cylinder MD730108
Clutch Slave Cylinder MD730108 Seller: Ningbo Motor Industrial Co.,ltd. Clutch Slave Cylinder MD730108 Clutch Slave Cylinder Application Summary:MITSUBISHI DELICA BOX (P...
Brake Disc 54032
Brake Disc 54032 Seller: Ningbo Motor Industrial Co.,ltd. Brake Disc 54032 BRAKE Disc Application Summary:Ford Product Description Rear axl...
Brake Master Cylinder 34 31 2 225 505
Brake Master Cylinder 34 31 2 225 505 Seller: Ningbo Motor Industrial Co.,ltd. Brake Master Cylinder 34 31 2 225 505 Brake Master Cylinder Application Summary:BMW 3 (E30...
Brake Pad D242
Brake Pad D242 Seller: Ningbo Motor Industrial Co.,ltd. Brake Pad D242 BRAKE PAD Application Summary:Toyota   Product Description F...