Cooling Tower Filler-VF610-LC
PRODUCT DESCRIPTION
Thecooling toweris acooling device, which makes the hot water in the tower be cooled mainly by the evaporative cooling of water. In order to make full use of water resources, reduce the load of urban tap water supply network, and reduce the operating cost, cooling water is treated bycooling tower and recycled.
“Fill” is a medium that used in cooling towersto increase the surface area available for the water.
In a cooling tower, the really important actually iscooling tower fill. Fill is a plastic sheet used incooling towersto build the more surface region of the tower. If we want to expanded surface, we need to take considers into making more contact about water and fills, so that water will have more surface area in the cooling tower fill.
make hot water have much more surface area with sheet and air and the medium of tremendouslyextended film fill,so that hot water is cooled quickly.
After be cooled the water is flow in a water container from which it is pumped again to cooling other hot water, and the warm air leaving the fill and releasing from the above of the cooling towers ,and like this Continuously cooling air from bottom and release warm air from above to keep cooling tower cooling hot water continuously, to reduce the load of urban tap water supply network, and reduce the operating cost, So that we could make full use of water resources.
Filler is the most important part of the cooling tower, and its efficiency depends on the extent to which the cooling water and air are fully in contact with the filler.Filler temperature 50 °C ~ 68 °C, anti-aging, excellent performance, anti-ultraviolet, long life.
should be made to have more contact about water and fills , and longest time as possible. Fill allows the water to form thin flowing sheets to expose as much water surface area as possible to the interacting flow.
|
Type |
VF610-LC |
|
Material |
PP/PVC |
|
Width |
305mm |
|
Length |
as your request |
|
Thickness |
from 0.28mm to 0.38mm |
Send product request
Other supplier products
 |
Cooling Tower Infill: CF1000-1300 | Cooling Tower Infill: CF1000-1300Width: 1000mmLength: 1300mmThickness: from 0.28mm to 0.45mmProfile height: 20mmMaterial: Virgin PVC or PPApplicati... |
 |
Cooling Tower Filler: CF1000-HT | Cooling Tower Filler: CF1000-HT Width: 800mm or 1000mm Length: as your request Thickness: from 0.28mm to 0.45mm Profile height: 20mm Material:... |
 |
Membrane tube diffuser | Membrane tube diffuserThe membrane tube diffuser is a new type of oxygenation aerator and the core equipment of A/O process (activated sludge bioch... |
 |
Cross Flow Cooling Tower Filler-CF1300-SP | -CF1300-SP introduction is one of the most important components for exchange of gas and water in cooling tower.is the major parts to improve the ef... |
 |
Cooling Tower Infill: PP CF750-LC | Cooling Tower Infill: PP CF750-LCWidth: 750mmLength: 400mm, 800mm, 1200mm, 1600mmThickness: from 0.28mm to 0.45mmProfile height: 20mmMaterial: Virg... |
Same products
 |
Medical Plastic Parts | Seller: Packson Mold Co.,Ltd | Project Management To be a qualified medical plastic components manufacturer, the most advanced ... |
 |
PA66 GF15 Heat Stabilized (A2006C, A2016C) for Engineering Plastics | Seller: Suzhou Anmei Material Technology Co., Ltd | PA 66 GF 15is a 15% glass fiber reinforced, heat-resistance, polyamide 66 resin for injection mol... |
 |
PA66 GF | Seller: Suzhou Anmei Material Technology Co., Ltd | Anmei focuses on the production of modified engineering plastics. We have polyamide pa6 6gfmodif... |
 |
Nylon6 PA6 | Seller: Suzhou Anmei Material Technology Co., Ltd | Other than fiber-reinforced pa6 polyamide, the unreinforced nylon type 6 produced by Anmei, one o... |
 |
Nylon 66 Pa66 With High Tensile Strength (A2307X01, A2317X01) for Engineering Plastics | Seller: Suzhou Anmei Material Technology Co., Ltd | Using Polyamide 66 as the basic resin, the tensile strength of nylon 66 is obtained by blending a... |
