Powder coating primer containing zinc
Product Description
MT-PZ is a powder coating primer containing zinc which is designed to give enhanced corrosion protection of mild steel. This duplex system combines cathodic protection and barrier effect. Dedicated to steel protection with a surface pre-treatment obtained by grit/shot blasting. MT-PZ is based on a specific epoxy zinc rich formulation that brings conductivity to enable the cathodic protection. MT- PZ includes a specific anticorrosive function which improves the protection in case of scratch. Qualisteelcoat approval: Base Material: Steel PE-0097 2 coat system – up to C4-H, mechanical pretreatment.
Powder Properties
| Chemical type | Thermosetting epoxy |
| Appearance | Smooth |
| Gloss level(60°) | 45-65units |
| Color | Grey (about RAL7012) |
| Recommended Film Thickness (µm) | 70 – 120 µm |
| Density (g/cm3) | 2.1g/cm³ |
| Application | Electrostatic |
| Storage | Under dry, cool (≤ 30°C) conditions |
| Shelf life | 12monthsbelow25°C |
Pretreatment
Surface preparation depends upon the metal, the type of surface, its conditions and the required performance. See our recommendation for pretreatment to be used with MT-PZ.
| Substrate | Mechanical pretreatment | Chemical pretreatment |
| Mild steel | Grit Blasting Sa 2.5 in accordance with ISO NF EN 8501-1. Roughness: Rz 35 60 µm / Ra 6-12 µm | Banned |
| Cast steel | ||
| Electro Zinc steel | Banned | |
| Hot dip galvanized steel | ||
| Zinc sprayed (gas flame/electrical deposition) |
Application
MT-PZ is suitable for corona electrostatic spraying. Tribo application is not recommended.
| Application settings | Fluidizing air pressure: 1.5kg/cm2 initially then 1kg/cm2
Transport air pressure: 0.5 to 0.8 kg/cm Recommended voltage: 65 to 70kV |
| Curing limits | Primer should be cured, or at least gelled, using the recommended curing schedules, before application of the topcoat. The object temperature must not be below 110°C or above 180°C.
The primer should be cured in a convection oven, optionally with infra-red heaters, with air temperature not exceeding 180°C. |
| Recommended film thickness | 70-120 µm A good protection is linked with the recommended film thickness. |
| Recycling | Trials, with suitable recycling equipment, must be carried out before commencing production. Attention should be paid to the ratio of new powder, a minimum of 70% must be used. Gun nozzles must be cleaned every 30 minutes. |
If you're ready to take the next step or Request Free Samples, Leave your message below and we’ll reply soon. 20+ years of chemical manufacturing & export experience, a partner you can trust.
Send product request
Other supplier products
 |
Amorphous aluminium silicate with a high degree of whiteness SODASIL P95 | Introduction CAS:1344-00-9 EINECS:215-684-8 Nature Amorphous aluminium and sodium silicate obtained by precipitation in an aqueous medium. Tec... |
 |
Powder coatings for Automotive trim parts MT-A2201/MT-YZ204I | Product Description MT- A2201 clearcoats can be used for pillars and appliqués, roof racks, grille guards, bumpers, and mirror housings, al... |
 |
Thermosetting Special Powder Coating | I. Product Introduction In today’s world where extreme performance and environmental protection are both highly valued, the thermosetting sp... |
 |
Talc Powder MT-TYT-3000A | Product Introduction MT-TYT-3000A is a high-grade talc powder produced by our company using internationally advanced airflow impact grinding techn... |
 |
Aerospace Powder Coating | Introduction Looking for premium powder coatings for aerospace and aviation components? We are a Chinese factory with over 20 years of export exp... |
Same products
 |
High Concentration Plastic Color Masterbatch Factory Direct Supply | Seller: 861445 | We are a professional color masterbatch manufacturer with years of R&D experience in plastic ... |
 |
Acid Ink Blue G Factory | Seller: TIANJIN LEADING IMPORT & EXPORT CO., LTD | Acid Ink Blue G Factory 【Application of Acid Ink Blue G 】 mainly used for making blue or ... |
 |
Acid Black ATT Factory | Seller: TIANJIN LEADING IMPORT & EXPORT CO., LTD | Acid Black ATT Factory 【What’s Acid Black ATT】 is made of acid black 10B and acid o... |
 |
Acid Black 10B Factory | Seller: TIANJIN LEADING IMPORT & EXPORT CO., LTD | Acid Black 10B Factory is mainly suitable for dyeing and printing wool ,silk and nylon fabri... |
 |
Sulphur Dyes | Seller: TIANJIN LEADING IMPORT & EXPORT CO., LTD | Sulphur Dyes BuyDye supplies a range of sulphur dyes for cotton-based textile dyeing, includ... |
