SUNKYE FIRING HEAD CONNECTOR FOR PERFORATING GUN EQUIPMENT
Sunkye produced head connectorhas dual high pressure 138Mpa (20,000PSI) benefit with glass sintered sealing (the air leakage rate: 1x10-3Pa.CM³ /s) technical, support environment temperature -60°C-200°C (harshness especial reach to 260°C max) against API-67 standard requested.
Perforation Gun, A device used to perforate oil and gas wells in preparation for production. Containing several shaped explosive charges, perforating guns are available in a range of sizes and configurations. The diameter of the gun used is typically determined by the presence of wellbore restrictions or limitations imposed by the surface equipment.
Perforation is an extremely important technique in petroleum exploration and recovery engineering, a major means of enhancing the recovery factor of gas and oil wells and also a typical method of tapping the potential of existing oil fields and increasing output.
Perforation completion is widely used worldwide and accounts for about over 90% of all well completions. Almost all reservoir beds can be opened by this method. In the method, in the course of gas and oil field exploitation the production casing is lowered and cemented and then special perforation instrument and devices are sent down to the predetermined depth and aimed at the target layer.
Through the key parts, the firing head connector
Sunkye Firing Head Connector for Perforating Gun Equipment in Downhole & Offshore Application-3
Sunkye Firing Head Connector for Perforating Gun Equipment in Downhole & Offshore Application-4
The perforator down in the well is ignited from the ground and the lined cavity charge (The propellant material is potassium perchlorate, an oxidizer that burns rapidly, creating CO2. As the shaped charges detonate, the propellant is ignited by extreme heat from the gun system. As it burns, the propellant generates CO2 at high peak pressures typically well above the formation fracture gradient.) is ignited which result in the detonation wave to transmit forward at a velocity of 7~8 km per second and high temperature and high-pressure shock waves are generated which penetrate through the casing, cement sheath and enter the stratum forming a hole canal, as illustrated by the diagram. Whichever perforation method you use, the performance and quality of the perforating gun (Including the perforating gun pipe) shall have a significant influence on the perforation quality of gas and oil wells.
|
PRESSURE FIRING HEAD CONNECTOR SPECIFICATIONS |
||
|
Firing Head Connector Part Number |
||
|
28±0.01 |
28±0.05 |
|
|
Pin connector Length mm |
65+0.1 |
41±0.05 |
|
200 |
200 |
|
|
1,800psi/12MPa |
1,800psi/12MPa |
|
|
20,000psi/138MPa |
20,000psi/138MPa |
|
|
Air Leakage Rate |
1x10-3Pa.CM3/s |
1x10-3Pa.CM3/s |
|
Shell Material |
X-750 |
X-750 |
|
Contact Material |
Alloy 52 Gold Plating |
Alloy 52 Gold Plating |
|
Rated Current per Pin |
5A |
5A |
|
Dielectric Strength |
≥5000MΩ |
≥5000MΩ |
|
Contact Resistance |
≤10mΩ |
≤10mΩ |
|
Life Time |
1000times |
1000times |
Benefits / Capabilities ofSunkye Firing Head Connector
Can re-perforate in old well without pulling the tubing out.
Can be used with big charges to achieve deeper penetration.
Firing circuitry is in short before the charges are released.
Dual Pressure random mounting side
Circulation flexibility—allowed in both directions before and after the guns are fired. Underbalanced perforating conditions are easily established.
CT compatibility—the firing head can take a combination of shear pins and can be connected to any CT string by means of a crossover connector.
Soldering mounting terminal Design efficient assembly to the equipment
Ultra-tiny design fit for the drill head solution and equipment
Assembly & Mounting Steps
Step 1: Annulus pressure from above the packer enters the crossover tool and is applied to the first (bottom) time delay firing head. The first Sunkyefiring sub prevents pressure from reaching the second firing head. The time delay provides time to bleed off pressure. When the guns detonate, the firing train continues to the firing sub. The sub fires, creating a path to the second firing head. The zone is tested.
Step 2: Annulus pressure is reapplied and travels to the second time-delay firing head. The first pressure isolation sub prevents pressure from venting through the first set of perforations. The pressure is released, the gun fires and the second Select Fire sub fires and opens a path to the third gun. Production from the second zone is commingled with pressure from the first zone for testing.
Step 3: Pressure applied to the annulus passes through the annulus pressure crossover and down the control line to the third time-delay firing head. The second pressure isolation sub prevents pressure from venting through perforations in the first and second zones. The pressure is released, the guns fired, and flow from all three are commingled for testing.
Sunkye is one of professional military connector manufacturers. We provide Micro Crimp Connectors, PCB Connectors, mil spec pinsand so on. Want to know more? Please contact us.
Send product request
Other supplier products
 |
MICRO SOLDER CUP CONNECTORS | Sunkyeis a global solutions provider of d sub connectorsolutions and differentiated products to the world-wide interconnector industry. Sunkye Mic... |
 |
Sunkye R04S Space Grade Micro D Solder Cup Type Connector | Micro-D Sub Connectorsfor space applications. Twist pin contacts, high density interconnection, 1.27mm contactspacing and 1.1mm spacing between ro... |
 |
Sunkye R066 MIL DTL 55302 Electric Rectangular Connector | Sunkye R066mil 55302Electric Rectangular Connector Brief Introduction of Sunkye R066 Electric Rectangular Connector Contact spacing: 1.905 mm Cont... |
 |
Sunkye Waterproof Ip68 Electrical Connector | Waterproof Ip68 electrical connectorsmeets with International Protection Marking, IEC standard 60529. Against test duration: 30 seconds in each of ... |
 |
Sunkye R04S Space Grade Micro D Right Angle To PCB Type Connector | space grade connectors Brief Introduction Micro-D connectors for space applications. Twist pin contacts, high density interconnection, 1.27mm conta... |
Same products
 |
Aluminum Conductor Steel Reinforced (ACSR) | Seller: HENAN HONREY CABLE CO.,LTD | Steel - cored aluminium stranded wire, it could also be described as ACSR Conductor or ACSR Alumi... |
 |
Aluminum Conductor Alloy Reinforced (ACAR) | Seller: HENAN HONREY CABLE CO.,LTD | As a kind of energy saving conductor, aluminium alloy core stranded wire is mainly used for power... |
 |
Aluminum Clad Steel Wire (ACS) | Seller: HENAN HONREY CABLE CO.,LTD | Aluminum clad steel wire, also known as acs conductor, can be used for ground wire and conductor ... |
 |
Aluminum Clad Steel Reinforced (ACSR/AW Conductor) | Seller: HENAN HONREY CABLE CO.,LTD | Aluminum clad steel core aluminum stranded wire is mainly used for overhead lines, compared with ... |
 |
Aluminum Alloy Conductor Steel Reinforced (AACSR) | Seller: HENAN HONREY CABLE CO.,LTD | Steel core aluminum alloy stranded wire is mainly used in long-span overhead transmission lines, ... |
