90 degree elbow pipe

• 

To understand the basic knowledge of an elbow, the determination of an elbow must know the diameter, radius, and angle of the elbow, and some have a straight section. According to the angle, there are, 45 ° and 180 °, which are the most commonly used, and other abnormal angle bends, such as 60°, are also included according to the engineering needs. The angle of the elbow needs to be measured with a tool, and only 180 degrees, 90 degrees, and 45 degrees can be seen.

offers a wide selection of pipe fittings, including the 3/4 street 90, short radius elbow, 90 degree elbow pipe, 90 degree elbow conduit, 1 2 90, and 6 inch 90 degree elbow. These high-quality fittings are essential for creating precise angles and bends in piping systems, ensuring efficient flow and easy installation. Whether you need a tight short radius elbow for space-constrained applications or a larger 6 inch 90 degree elbow for industrial systems, Jianzhi provides reliable and durable solutions to meet the specific requirements of any project. Jianzhi offers a comprehensive selection of 90 fittings, designed to facilitate seamless changes in direction within piping systems. These fittings are crafted from high-quality malleable iron and undergo a rigorous manufacturing process to ensure durability and reliability. Ideal for both residential and industrial applications, Jianzhi 90 fittings provide optimal flow characteristics and are easy to install, making them a practical choice for any plumbing or heating project. With a commitment to quality and customer satisfaction, Jianzhi continues to be a trusted supplier for all your fitting needs.

Formula for calculating the size of the elbow:

1. 1. 5 times the center height of the elbow = path 1.524, in fact, is the path multiple, the number after the decimal point of the resulting result is round to the nearest integer, such as the path of 219 is 200. The center height is 200 ≤ 1.524 ≤ 304.8, take 305; if the path of 114 is 100, the center height is 100 ≤ 1.524 ≤ 152.4, take 152.
   (suitable for DN100 and above elbow curvature radius algorithm for convenient and fast calculation).

2. Stamp height = center height + radius of elbow, such as 1.5 times diameter 219 elbow height = 305 x 219 ≤ 2 ≤ 305 ≤ 109.5 ≤ 414.5.

3. The outer arc length = (center height + radius) 3.14 ≤ 2 ≤ 360 degrees, that is, (stamp height) 3.14 ≤ 2 ≤ 360 degrees, from which the outer arc length of elbow can be calculated = poke height * 3.14 × 2.

4. Inner arc length = (center height-radius) 3.14 ≤ 2 ≤ 360 degrees.

5. The blanking length of the elbow = the height of the center of the elbow 3.14 ≤ 2 the outer diameter of the elbow / pipe diameter + (pipe wall thickness * 3) + machining allowance, such as using 180 × 8 pipe blanking, pushing 273 elbow, the above formula can be calculated:
   The blanking length is 381 ≤ 1.57 ≤ 273 / 180 / 24 / 931.22 mm + processing allowance.

Calculation Formula for a 45-Degree Elbow in a Pipeline

1. The calculation method for the short pipe in the middle of two 45 degree bends is as follows: short connection length = height difference x 1.4142 ≤ 0.8284R, R = bending radius of elbow (that is, the length of a 90 elbow fitting bending head).

2. First of all, calculate the center height. Then the central length minus the height of the elbow on both sides is the short pipe length in the middle.
   The elbow requires the radius of curvature to be controlled. For example, if the radius length is 1.5D, the curvature radius must be within the required tolerance range. Because most of these pipe fittings are used for welding, in order to improve the welding quality, the end of the car must be inserted into a groove, leaving a certain angle, with a certain edge. This requirement is also relatively strict, depending on how thick the edge is, how much angle and deviation range are specified, and the geometric of the pipe fittings.

Formula for calculating center to end distance of such elbows is as follows:

For standard degrees of pipe elbows such as 45° and 90°, elbow center to end dimensions are available in standard pipe charts. But many times, custom elbow angles are required at site which should be cut from standard 45° or 90° elbows.

Elbow length in mm = Tan(Elbow Angle/2) X Elbow Radius in mm

Where:

The center to end dimension for 90° Long Radius elbows, as listed in ASME B16.9 dimension tables, is equal to the elbow’s radius. Tan(90/2) i.e. Tan 45 is 1, which is why.

Typically, 90 degree standard elbows are used to cut custom elbow angles between 45 and 90 degrees. However, elbows with custom angles less than 45 degrees are typically cut from the 45 degree standard elbow. To find the elbow radius for a conventional 45-degree elbow, divide the center-to-end measurement given in the dimension tables by Tan (22.5). The elbow angle for custom degrees can then be obtained using the aforementioned formula.

Same procedure applies to 3D elbows.

Technical specifications needed to make elbows:
Controlling the radius of curvature is necessary. For instance, the radius of curvature needs to fall within the necessary tolerance if the radius is 1.5D. Since the majority of these fittings are used for welding, the ends are car-grooved to leave a specific angle and edge. This requirement is more stringent since the edge must be thick, the angle must be determined, and the deviation range must be observed. Certain provisions have far larger geometric measurements than fittings. The elbow’s mechanical characteristics and surface quality are essentially the same as those of the tubes. The pipe that needs to be joined has the same steel material for ease of welding.

For example, if the elbow dimensions are 10 inches by 90 degrees, the path D is 250 and the center height is 250 * 1.524 = 381. The algorithm for calculating the radius of curvature of DN100 and above is quick and simple to use.

1.1.5 times the center of the elbow height A = diameter 1.524; in fact, the path diameter D multiples. The decimal number of the result will be rounded to the nearest integer number.

2.Poke height is equal to the center height plus the elbow’s radius; for example, a 10-inch, 90-degree elbow with a 273-diameter would have 305+273/2=441.5 in Poke height.

3.The outer arc length of the 90 degree elbow can be computed as follows: stamp High 3.14/2. The outside arc length of the elbow is equal to (center height + radius) 3.14 2/360 degrees, or (poke height) 3.14 2/360 * degrees.

4.(Central height – radius) 3.14 2/360 * degrees is the length of the inner arc.

The theoretical weight of the elbow

Weight of elbow = (outer diameter-wall thickness) wall thickness 0.02466 length.
1) The outer diameter is not equal to the nominal diameter, equal to the outer diameter at the groove of series 2.
2) length = 2 π R angle / 360, the calculated weight length of the elbow is the arc length corresponding to the angle of the elbow in the circumference of R as the radius.
3) R is the bending radius of the elbow.

Other supplier products

	4 way pipe connector	are multi-joint fittings that connect four pipe sections together at a central junction point. They are commonly used in plumbing, drainage, and i...
	black iron fittings	A Black Iron union tail is a detachable fitting used for accessory replacement. It’s part of a union and typically consists of a male tail, a...
	male to female pipe fittings	Cross pipes are an essential part of any piping system, connecting different pipes and allowing for changes in direction and connections between pi...
	galvanized pipe	Galvanized pipes are steel pipes coated with a protective layer of zinc, offering exceptional resistance to corrosion and rust. Widely used in plum...
	g.i coupling	A is an essential component in plumbing and piping systems used to connect, control, and direct the flow of fluids such as water, gas, and other l...

Same products

	pipe union fitting	Seller: Jianzhi Pipe Fittings	Union pipe fitting / Pipe union A is a threaded fitting which allows the pipe work to be separa...
	5 way pipe fitting	Seller: Jianzhi Pipe Fittings	Cross pipes are an essential part of any piping system, connecting different pipes and allowing f...
	45 degree elbow pipe	Seller: Jianzhi Pipe Fittings	If you’re working on a plumbing project, you may have encountered the term “45 degree...
	male to female pipe fittings	Seller: Jianzhi Pipe Fittings	Cross pipes are an essential part of any piping system, connecting different pipes and allowing f...
	4 way pipe connector	Seller: Jianzhi Pipe Fittings	are multi-joint fittings that connect four pipe sections together at a central junction point. T...