Ignition temperature tester
Introduction
The Minimum Ignition Temperature Tester is a way of testing the sensitivity of the ignition that the dust cloud is in the heated environment. When a lot of dust is exposed in heating the air and the air temperature is high enough, it may lead to spontaneous combustion. This method can test the minimum ignition temperature of combustible dust cloud.
Standard
· IEC 61241-2-1:1994:Electrical apparatus for use in the presence of combustible dust - Part2: Test methods - Section 1: Methods for determining the minimum ignition temperatures of dust;
· EN 50281-2-1:1999:Electrical apparatus for use in the presence of combustible dust - Part 2-1: Test methods - Methods for determining the minimum ignition temperatures of dust
Testing process
The Test is carried on the in Godbert-Greenwald furnace. The heating furnace is consist of the vertical quartz tubes . The hole is at the bottom of the tube.The glass observing room is connected with sample fixing device at the top of the quartz tubes. The compressed air from the tank blows the dust into the heating furnace and the sample fixing device ,and then exposed into the glass observing room and the quartz tubes .the heating furnace is located on the holder . And you can observe the ignition appearance from the bottom of the furnace. The test begins from the 500ºC. If you observe the ignition appearance ,you shall decrease the temperature at the 10ºC,until the ignition does not appear.
Technical parameters
1. MCU control, easy to use and maintain
2. The copper ingot furnace is 100mm in diameter and 100mm in height, and has 4 container holes
3. Stainless steel container with inner diameter of 9mm, height of 48mm, wall thickness of 1mm, with a length of 10mm, inner diameter of 1.5mm nozzle cover.
4. Voltage and power :220V+10%V, 50HZ, power about 500W5. Butane igniter inner diameter 0.8mm+0.1mm nozzle, flame height 10mm-20mm can be adjusted
5. The copper ingot furnace can be constant at any temperature between (150-450)℃
6. Temperature control accuracy :±2℃
Send product request
Other supplier products
 |
Tipping Frames | STD-5D Adjustable for different drum sizes Compatible with TONSON valves for flow control Pneumatic dumping (saves time and labor) Drum mouth h... |
 |
Automotive Wires Liquid Resistance Tester-QINSUN | Test Standards: Requirements for liquid resistance tests of automotive wires in ISO 6722. SAE J1128. QC/T 730. and JASOD611 Main Parameters: T... |
 |
(Changan) Automobile wire and wire bending testing machine-QINSUN | Standard: DIN 51211 and ISO 7801 Scope of application: Changan Automobile "JT automobile low-voltage wire technical conditions" standard Techni... |
 |
Wyzenbeek or Oscillatory Abrasion Tester-QINSUN | Product introduction: Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of f... |
 |
Reciprocating Wear Tester | Standards ASTM Standards: Formulated by the American Society for Testing and Materials (ASTM), standards such as ASTM D6079 are used to evaluate... |
Same products
 |
Metal Ring-and-Block Friction and Wear Tester | Seller: Standard Groups | This friction and wear tester is designed and manufactured in accordance with the national standa... |
 |
Sliding Bearing Fatigue Testing Machine | Seller: Standard Groups | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
Sliding bearing PV friction testing machine | Seller: Standard Groups | The sliding bearing PV friction testing machine is primarily used to evaluate the friction and we... |
 |
High temperature vacum friction & wear tester | Seller: Standard Groups | High temperature vacuum friction and wear testing machine is mainly used to study the friction an... |
 |
Dry Sand Rubber Wheel Wear Tester | Seller: Standard Groups | Dry and wet sand abrasive wear testing machine is mainly used to evaluate the wear resistance of ... |
