PLC liquid crystal touch impact testing machine (simple suspension)
Product Introduction:
Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.
Standards:
GB/T 11022-2020. GB/T 3906-2020. JB/T 10840-2008.GB/T 7251.1-2013 ，GB/T 7251.4-2017.GB/T 7251.5-2017 ，GB/T 20641-2014
GB/T 20138-2006 ，GB/T2423.55-2006 ，Q/GDW11008-2013
Main features:
Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.
Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.
Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.
Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.
Performance parameters:
1. Simple beam impact testing machine
- Impact speed: 2.9m/s
- Impact energy: 1/2/4/5J
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 230mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
2. Cantilever beam impact testing machine
- Impact speed: 3.5m/s
- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 335mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
Send product request
Other supplier products
 |
Automotive Wires Low - temperature Impact Tester | Test standard: ISO 6722. ISO 14572. ISO 19642. SAEJ 1128. QC/T 730. JASOD611-2009 Technical parameters: 1) Low temperature impact height: 50-2... |
 |
Fabric UV resistance tester | Product details It includes the closest spectral characteristics of the sun's light source, high stability of the UV-visible spectrophotometer, ... |
 |
DSC Differential Scanning Calorimeter | The Differential Scanning Calorimeter (DSC) measures the heat flow to or from a sample under controlled heating conditions. A small amount of sampl... |
 |
Automotive Connectors Salt Spray Tester | The salt spray tester for automotive connectors is suitable for testing the corrosion resistance of various material surface treatments, includin... |
 |
45-degree dry cleaning tester | Product Introduction: The instrument is composed of a bottom plate, a control panel and a drum. The clothes to be washed and the dry cleaning agen... |
Same products
 |
Metal Ring-and-Block Friction and Wear Tester | Seller: Standard Groups | This friction and wear tester is designed and manufactured in accordance with the national standa... |
 |
Sliding Bearing Fatigue Testing Machine | Seller: Standard Groups | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
Sliding bearing PV friction testing machine | Seller: Standard Groups | The sliding bearing PV friction testing machine is primarily used to evaluate the friction and we... |
 |
High temperature vacum friction & wear tester | Seller: Standard Groups | High temperature vacuum friction and wear testing machine is mainly used to study the friction an... |
 |
Dry Sand Rubber Wheel Wear Tester | Seller: Standard Groups | Dry and wet sand abrasive wear testing machine is mainly used to evaluate the wear resistance of ... |
