Chrysler Flex Fold Tester

• 

Flex and Fold Tester determines the breakdown resistance of leather, vinyl coated fabric, synthetics, rubberoids, paper, and the like. Product applications which call for flexing and folding may cause your material to split, crack, craze, or separate at the seam. To predict these types of degradation, it is important to simulate the mechanical action taking place in your product's service life environment. The flexing action replicates the physical stresses normally exerted on fabrics and other materials in various automotive, commercial and industrial environments, allowing you to predict the durability of the materials when assembled in their final form.

Test specimens are easily clamped into one of four sample positions. Three of these positions perform flex testing. The sample is held under a uniform tension of the while moving one end of while moving one end of the sample through a given distance each side of the perpendicular. This action creates flexural stresses and strain on the sample, which simulates normal wear and causes the material to break down. A change in length of the sample gives a further indication of the material's breakdown.

Once elongated to the point of failure, the bottom of the sample holder triggers a shut-off switch to automatically conclude the test. Upon conclusion of the test, the operator may record the number of cycles indicated on the cycle counter, remove the failed specimen and restart the test for the remaining samples.The fold test is conducted on the fourth sample, which is clipped into place between two plates at the far end of the instrument. The sample is folded against itself with the finish side out when the two plates are pressed together under a specified tension.Optional digital cycle counter is available.

Chrysler Flex Fold Tester Technical Parameters:

1.Tabletop design.

2.Capacity for testing three flex specimens simultaneously.

3.One fold sample capacity.

4.Each specimen holders may be tensioned individually.

5.Stroke Length: 2.75 inch.

6.Clamp separation: 152mm (6inches).

7.Stroke Rate: 35 CPM.

8.Tension Load: 8 lbs. Adjustable.

9.Pressure plate load: 641N (12lbf) when closed.

10.Specimen size, flex: 76×203mm(3×8inches).

11.Specimen size, fold: 129×129mm (5×5inches).

12.Electronic cycle counter with reset.

13.Electronic counter: 6 digit.

14.External dimension: 36×12×22inches (L×D×H).

Other supplier products

	Yarn Twist Tester	Application ScopeThe yarn twist tester is an instrument used to measure the twist of yarns and their related technical indicators.Applicable Standa...
	Single-Flame Source Tester En ISO 11925-2	This instrument is designed according to ISO 11925-2. it is used to test building material under conditions in the absence of external radiation to...
	Stone chip tester manufacturer	The Gravel Resistant Impact Tester/Stone Chip Tester is specifically designed for gravel impact testing of automotive materials and surface coating...
	Textile Far - Infrared Radiation Heating Tester - lab instrument	With the continuous advancement of technology, new types of fibers and textile products have emerged, leading to increasingly high demands on texti...
	Snap button tester	Thebutton snap pull testing machineis gripped by the Upper Snap Clamp and the garment is fixed to the lower Fabric Clamp. By turning the hand wheel...

Same products

	Air Intake Filter Test System	Seller: Standard Groups	The Air Intake Filter Test System is designed for testing industrial air filters and engine air f...
	Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging	Seller: Standard International Group (HK) Limited	The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f...
	Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester	Seller: Standard International Group (HK) Limited	The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter...
	HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine	Seller: Standard International Group (HK) Limited	The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ...
	VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine	Seller: Standard International Group (HK) Limited	The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia...