Micro-Scale Abrasion Tester
The STD-TE 66 Micro-Scale Abrasion Tester is used for determining the wear coefficient of hard and soft coatings and monolithic materials by abrasive wear, in a ball on plate contact configuration. The machine may also be used as a crater-generating tool on coated surfaces for coating thickness determination. Tests can be performed in accordance with BS EN 1071-6: 2007: Advanced technical ceramics – Methods of test for ceramic coatings – Determination of the abrasion resistance of coatings by a micro-abrasion wear test.
Description
Other ball-cratering devices use a free ball that rests on the coated surface and at two points on a rotating shaft. The static load on the surface is determined by the size of the ball and the tilt angle of the coated surface. The ball is driven by friction against the shaft and abrasive slurry is fed into the wearing contact. As the ball is free and the friction conditions variable, the rotational speed, number of rotations and applied load are both uncertain.
In the STD-TE 66 the ball is clamped into a rotating shaft and the test surface is mounted on a counterbalanced beam that hangs vertically from a pivot. This configuration offers the following advantages over the free ball:
• The load is defined precisely and without interaction with the friction force.
• A wide range of loads can be applied, without the need for variable ball sizes.
• Rotational speed of the ball and number of cycles completed is measured precisely.
A 25 mm ball is clamped between two coaxial shafts each carried in support bearings. One shaft is driven by a variable speed dc geared motor. A batch counter is provided to measure and control the number of shaft revolutions.The rotation of a ball against a coated plate in the presence of an abrasive slurry results in the production of a circular depression. Eventually the coating is worn through and a “bulls-eye” depression is seen where the substrate shows through. Measurements of the inner and outer diameters of this bulls-eye are easily made and provide an accurate and low cost method of determining coating thickness. This is an established coating thickness measurement technique.
For wear coefficient determination, periodic measurement of wear is made, using an integral digital microscope. The crater is viewed by rotating the load arm to bring the sample out of contact with the ball, thus avoiding disturbance to the contact, by removal of the ball.
Technical Specifications
| Ball Speed Range: | 30 to 150 rpm |
| Load Range: | 0.05 to 5 N |
| Ball Diameter: | 25 mm |
| Pump Feed Rate: | up to 60 ml/hour |
| Digital Camera: | 5MP CMOS USB Camera |
| Magnification: | x3 and x5 |
| TE 66/LC Line Contact Adapter | |
| Disc Diameter: | 25 mm |
| Disc Width: | Up to 10 mm |
| Services | |
| Electricity: | 220/240V, single phase, 50 Hz, 120 W |
| 110/120 V, single phase, 60 Hz, 120 W | |
| Installation | |
| Bench-mounting machine: | 720 mm x 440 mm x 570 mm high, 15 kg |
| Bench-mounting cabinet: | 530 mm x 420 mm x 320 mm high, 10 kg |
| Packing specifications: | 0.21 m3, GW 50 kg, NW 25 kg |
Send product request
Other supplier products
 |
Water Cooled Xenon Lamp Testing Chamber | STANDARD: Xenon Weather Test Chamber Material: Stainless Steel Temp. Range: RT-85º C Interior Dimensions: 500× 600×50... |
 |
Textile Drying Time Tester | The Textile Drying Time Tester is a precision instrument designed to measure evaporation rate and drying time of textiles under controlled environm... |
 |
Steel Shank Fatigue Resistance Tester | Shank fatigue resistant test is suitable for the test shoes with the core of the resistance to fatigue. The principle is the core of both ends wit... |
 |
Rubbing Color Fastness Tester | Testing Equipment | Manual friction fastness tester is the most commonly used instrument for the textile industry to detect the color fastness of the fabric to dry and... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | A Light Fastness Tester, or Xenon Tester, Accelerated Ageing Chamber, is used for xenon arc testing in dye fastness tests for lightfastness and wea... |
Same products
 |
Blanket Flammability Test Machine | Seller: Standard Groups | Bed Blanket Flammability Tester-It is mainly used for testing the flame retardant performance of ... |
 |
High Temperature Oxygen Index Tester | Seller: Standard Groups | The High-Temperature Oxygen Index (TOI) measuring instrument determines oxygen index at up to 125... |
 |
Limiting Oxygen Index Tester | Seller: Standard Groups | The Limiting Oxygen Index Tester measures the minimum oxygen concentration needed to sustain comb... |
 |
Vertical Flammability Tester | Seller: Standard Groups | Vertical Flammability Chamber for measuring the vertical flame spread for children’ sleepwe... |
 |
45 Degree Flammability Tester | Seller: Standard Groups | Application 45 Degree Flammability Tester is used to determine the burning characteristics of te... |
