Transparent Absorbing Wave Temperature and Humidity Vibration Test Chamber

Get a quote：

Whats/App: +86 181 0160 0864

The Transparent Absorbing Wave Temperature, Humidity, and Vibration Test Chamber is a high-end environmental simulation system engineered for integrated reliability testing. It distinguishes itself by combining traditional environmental stressors—temperature, humidity, and vibration—with specialized electromagnetic wave transparency and absorption capabilities. You can utilize this chamber to simulate the complex operational environments faced by electronic systems, allowing for the simultaneous application of thermal cycling, moisture, and mechanical vibration while maintaining the integrity of RF signals. This multi-stress approach is essential for identifying latent design flaws in high-frequency communication equipment and radar components before they reach the field.

Applications

The Transparent Absorbing Wave Temperature and Humidity Vibration Test Chamber is a high-end testing device capable of simulating complex environmental conditions. It is particularly well-suited for reliability verification in fields such as aerospace, aviation, and automotive electronics. By superimposing temperature-humidity cycles with vibration stress, it rapidly exposes potential defects in products during transportation or use.

Standards

JJF 1101 Calibration Specification for Temperature and Humidity of Environmental Test Equipment

GB/T 5170 Inspection Methods for Environmental Test Equipment for Electrical and Electronic Products

Features

ombined temperature, humidity, and vibration testing to simulate real-world multi-stress environments

High-performance transparent wave door with excellent X-band transmission efficiency

Integrated absorbing wave materials to minimize electromagnetic reflection and standing wave interference

Wide temperature and humidity operating range suitable for extreme environmental testing

High thermal load capacity to support powered test samples during operation

Stable structural design ensuring long-term flatness and mechanical reliability

Parameters

Category	Item	Specifications
Basic Specifications	Nominal Inner Volume	9.5 m³
	Inner Chamber Dimensions	2700mm × 1800mm × 1950mm (Depth × Width × Height)
	Test Environment Conditions	Ambient temperature: 25°C, relative humidity: ≤85% RH, cold water temperature: ≤28°C
Temperature Performance	Temperature Range	-70°C ~ +100°C
	Temperature Fluctuation	≤±0.5°C
	Temperature Deviation	≤±2°C
	Temperature Uniformity	≤2°C
	Temperature Ramp Rate	- Heating: ≥10°C/min (equivalent load 1000kg, electric heating power 8kW, average across the whole range; ≥10°C/min from room temperature to -55°C, ≥10°C/min from -55°C to 70°C)- In the range of -55°C ~ +85°C, the chamber can withstand an internal heat load of 8000W- In the range of -55°C ~ +85°C, the chamber can withstand an internal heat load of 3500W and an internal cooling air supply of 100kg/h (air temperature: 2~35°C, dew point temperature: ≤40°C)
Humidity Performance	Humidity Range	35% RH ~ 98% RH (adjustable within -20°C ~ 70°C)
	Humidification Method	Humidification via hot air passing through the test piece; alternating temperature and humidity (typical value: 30°C/60°C, RH95%, temperature change rate ≥85%); constant temperature and humidity (typical value: 35°C, 90% ~ 98%)
	Humidity Deviation	≤±3% RH (when humidity >75% RH); ≤±5% RH (when humidity ≤75% RH)
Chamber Front Door	Door Configuration	Hermetic door with transparent viewport- Temperature resistance: -65°C ~ +105°C- Humidity resistance: 25% ~ 98% RHFunctional performance:1) Working frequency: X-band2) Temperature resistance range: -65°C ~ +105°C3) Humidity resistance range: 25% ~ 98% RH4) Wave transmission rate: >95%5) Standing wave ratio influence: <2%6) Power resistance: 10W/cm²7) Flatness: <2cm (diagonal), no deformation after fabrication8) Fixing method: High-strength adhesive bonding to the chamber frame
Chamber Front End	Absorber Material (on Hermetic Door)	- Wave transmission rate (X-band): >95% (on left, right, and upper sides)- Power resistance: 10W/cm²- Total mass loss (TWC): ≤0.6%- Volatile condensable material (CVCM): ≤

Accessories

The standard and optional accessories available for your test requirements include:

Vibration interface platform and mounting fixtures

High-strength adhesive bonding system for transparent wave door installation

High and low temperature resistant absorbing wave materials for internal chamber surfaces

Temperature and humidity sensors with calibration support

Safety protection and monitoring modules

Test Procedures

To conduct a standard combined environmental test, you should follow these steps:

Install the test specimen securely on the vibration platform and connect required power and signal interfaces.

Set the desired temperature, humidity, and vibration profiles according to the test specification.

Start the temperature and humidity control system and allow conditions to stabilize.

Activate the vibration system and run the combined environmental test for the specified duration.

Monitor key parameters throughout the test and record all relevant data.

After test completion, return the chamber to ambient conditions before removing the specimen.

Other supplier products

	Automotive Floor Mat Abrasion Tester	Get a quote： Whats/App: +86 181 0160 0864 The Automotive Floor Mat Abrasion Tester is a specialized testing device designed for evaluating the ab...
	Walk-in High Low Temperature Low Pressure Test Chamber	Get a quote： Whats/App: +86 181 0160 0864 TheWalk-in High/Low Temperature and Low Pressure Test Chamberis a precision environmental simulation in...
	Catheter Leakage and Compliance Tester	Standards YY/T, etc. Main Uses The catheter leakage and compliance tester is mainly used to detect the leakage and compliance of medical cathete...
	Textile Flatness Tester	Getaquote: Whats/App: +86 181 0160 0864 The Textile Flatness Tester is a precision instrument designed to evaluate fabric surface evenness by qua...
	Stainless Steel Envirotronics Chamber | Useful and durability	Environmental Test Chamber is designed for laboratory experiments, product reliability testing, and programmable controls, providing a wide range o...

All supplier products

Same products

	HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line	Seller: Shandong HUASU Plastic Technology Co.,Ltd.	The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi...
	PanEVAP & MVR system	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...
	PanGAP wide gap welded plate heat exchanger	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel...
	PanBloc welded plate heat exchanger	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac...
	PanBox welded plate heat exchanger	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated...