Fabric Negative-ion Concentration Tester
Getaquote:
Whats/App: +86 181 0160 0864
Fabric Negative-ion Concentration Testers typically detect the amount of negative ions generated by fabrics based on principles such as triboelectricity, release from natural minerals, or photocatalysis. During the test, the fabric sample is placed in a specific environment, simulating real-world usage scenarios (such as friction and light exposure) to stimulate the fabric to release negative ions. The instrument uses a highly sensitive negative ion sensor to measure the number of negative ions released by the fabric in real time and accurately, and automatically calculates the average value to ensure the accuracy and reliability of the test results.
Applications
Functional Textile R&D: Assesses air-purifying, health-enhancing, and antimicrobial fabrics.
Quality Control: Verifies compliance with negative-ion standards for medical textiles, bedding, and apparel.
Certification Laboratories: Provides data for GB/T 30128-2013 certification.
Standards
GB/T 30128-2013: Textiles – Test and Evaluation of Negative Ion Generation
Features
Dual Friction Disc Design:
Upper Static Disc: Diameter 100 ±0.5 mm (fixed).
Lower Dynamic Disc: Diameter 200 ±0.5 mm (rotating at 93 r/min).
Capacitive Ion Sensor: High-sensitivity detection of activated negative ions.
Technical Parameters
| Parameter | Specification |
|---|---|
| Control Mode | Automatic (PLC) |
| Ion Collection Method | Capacitive Suction (Mobility >0.15 cm²/(V·s)) |
| Measurement Range | Range 1: 0–20.000 units/cm³ Range 2: 0–200.000 units/cm³ Range 3: 0–2.000.000 units/cm³ |
| Resolution | 10 units/cm³ |
| Friction Disc Speed | 93 ±1 r/min (Adjustable) |
| Applied Pressure | 7.5 ±0.2 N |
| Test Chamber Size | 300 ±2 mm × 560 ±2 mm × 210 ±2 mm |
| Power Supply | AC 220V ±10%, 50Hz |
| Dimensions (L×W×H) | 600 mm × 620 mm × 520 mm |
| Net Weight | 55 kg |
Test Procedures
1. Preparation Stage
Equipment Check
Connect the ground wire to ensure instrument grounding safety;
Confirm power supply stability, turn on the instrument switch, and warm up for 1 minute.
Sample Preparation
Cut the sample according to standard (e.g., A4 size), distinguishing the test surface (usually the skin-contact surface);
Ensure the sample is free of impurities and radioactive material contamination.
2. Parameter Settings
Mode Selection
Select “Negative Ion Detection Mode” on the operation panel;
Set the ion mobility (default ≥0.15 cm²/(V・s), meeting product accuracy requirements).
Range and Pressure Adjustment
Select the range according to the sample type (0-20.000/200.000/2.000.000 units/cm³);
Adjust the test pressure to 7.5±0.2 N (adaptable to different fabric types).
3. Testing Process (Simulated Friction + Ion Detection)
Sample Fixation
Lay the sample flat on the test stage, start the PLC to control the friction disc (rotation speed 93±1 r/min), simulating the friction state in actual use.
Ion Detection
Activate the capacitive attraction ion acquisition module to capture negative ions released during the friction process;
The instrument records the ion concentration in real time and generates a time-varying curve (supporting dynamic analysis).
4. Data Reading and Calibration
Record after reading stabilizes
Wait for the value to stabilize (display fluctuation ≤ ±2), then read the current negative ion concentration;
If "1" is displayed, switch to a higher range.
Calibration (if necessary)
Press and hold the "RE-ZERO" button for 3-5 seconds until the displayed value is between -0.01 and 0.01. then complete the zeroing.
5. End and Data Processing
Stop Testing
Turn off the friction system and remove the sample;
Save the real-time data curve and automatically calculate the average value.
Result Calculation
Repeat the test on 3 groups of samples and take the average value as the final result (unit: ions/cm³);
Data must comply with the requirements of GB/T 30128-2013 standard.
Send product request
Other supplier products
 |
Carbon Black Content Tester / Carbon Black Content Apparatus | Standard GB 13021-1991: Determination of carbon black content in polyethylene compounds. GB/T 2951.41-2008: Test method for carbon black and ash ... |
 |
Geosynthetic creep tester 丨Geotextile Test Machine | Scope of application: STD DW1290 series geosynthetics creep test system is used to determine the tensile creep properties of geosynthetics product... |
 |
Shoelace anti-siphon tester 丨Shoelace Tester | Product Introduction Shoelace anti-siphon tester is suitable for all kinds of waterproof leather, leather, mesh, waterproof shoelace, ribbon water... |
 |
Digital display electronic ink viscosity meter | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk A Digital Display Electronic Ink Viscosity Meter is a laboratory or production ins... |
 |
Fully Automatic Dual-Plate Thermal Conductivity Tester (Guarded Hot Plate Method) | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk Fully Automatic Dual-Plate Thermal Conductivity Tester (Guarded Hot Plate Method) ... |
