ISO 105 X11 ironing sublimation color fastness tester manufacturer
Get a quote：
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Features
Upper and lower heating module independent temperature control
The upper and lower inde pendent temperature control system adopts PID temperature control program, with features of high temperature control precision, low heating overload efficiency, and equipped with PT 100 temperature sensor.
Floating pressurized design
The floating design is carried out when the load is pressurized, allowing the testing of materials of different thicknesses. The pressure distribution and uniform heating can still be ensured in case of testing thicker materials.
Independent temperature control system
The timer is configured to preset the test time. It is automatically start the test timing once the upper platen is pressed downwards, and the buzzer is configured to prompt the test end.
Unique appearance design
The appearance of the tester is exquisite and beautiful. The insulation around the upper and lower heating plates is designed with insulation material to ensure that the heat of the heating plate is not transmitted to the outer casing, which is safe and reliable.
Technical Parameters
|
Test hot plate:W100 X D40mm (same of the upper and lower) |
Tem perature control: independent control of the upper and lower |
|
Heating plate metallurgy: high purity aluminum |
Warming-up time: user-defined |
|
Timer: preset time, automatic timing once the upper plate pressing downwards. |
Applicable test: hot pressing, dry heat, dimensional stability |
|
Heating range: ambient temperature -300°℃ |
Time alarming: buzzing alarm |
|
Hot panel pressure:4±1 KPa(40cm2) |
Weight 25kg |
|
Power:220V 1.6Kwindependent control of the upper and lower |
Power supply: 220V 50Hz |
|
Appearance size:400mmX400mmX450mm |
Test Procedures
First, adjust the working environment to meet JIS L0803 standard conditions: temperature 20±2℃ and relative humidity 65±3%. Acclimatize both the instrument and test samples in this environment for at least 4 hours. Then, cut textile samples into 150mm×50mm pieces (one piece per workstation), ensuring no wrinkles or defects. Finally, check the instrument: confirm it’s connected to the correct power supply (e.g., AC 220V/50Hz) and inspect rubbing heads and workstations for intactness.
Turn on the "Power" button on the control panel. Set test parameters according to relevant JIS standards (e.g., JIS L0849 or JIS K6328): adjust the pressure to 4.9N (the standard value for JIS tests), set the reciprocating speed to 30 cycles/min, and input the required rubbing cycles (e.g., 20 cycles for JIS K6328). Verify all parameters on the digital display to ensure accuracy.
For each workstation, fix the prepared sample flat on the test stage (use clamps to avoid displacement during testing). Attach a JIS L0805 standard white crocking cloth (50mm×50mm) to the bottom of each rubbing head, and secure it tightly with the clamping ring to prevent slipping during friction.
Initiate the TestAfter confirming all samples and components are properly installed, press the "Start" button to begin the test. Monitor the instrument’s operation throughout; if abnormalities occur (e.g., sample shifting, unusual noise), press the "Emergency Stop" button immediately. The instrument will stop automatically once it completes the preset rubbing cycles.
Press the "Stop" button, then carefully remove the crocking cloths and tested samples. Evaluate the results using the JIS L0805 grey scale: grade both the staining of the crocking cloth and the discoloration of the sample (on a scale of 1 to 5. where 5 indicates the best fastness). Record all test details (sample information, set parameters, and evaluated grades) in a test log for future reference.
Turn off the power and disconnect the instrument from the power supply. Wipe the sample stage, rubbing heads, and control panel with a dry, clean cloth to remove debris. Store unused standard crocking cloths in a dry, sealed container, and keep the instrument in a dust-free, dry environment when not in use.
Send product request
Other supplier products
 |
High Precision Surgical Needle Strength Testing Instrument Factory | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Suture Needle Penetration and Bending Strength Tester is a device used to... |
 |
Closed - Space Tester for Aerosol Sprays | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Description Conforms to UN Recommendations on the Transportation of Dangerous Good... |
 |
Dry Sand Rubber Wheel Wear Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of... |
 |
ASTM D1603 Carbon Black Measurement Machine | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications The Carbon Black Content Tester has wide applications in indust... |
 |
Automatic scratch resistance tester for coatings | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Coating Scratch Resistance Tester is used to evaluate the scratch resistance of coating... |
Same products
 |
ER4047 Aluminum Mig Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing reliable welding material... |
 |
ER4043 Silicon Aluminum Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing high-quality welding mate... |
 |
Choosing the Right Equipment for Heavy-Duty Cleaning | Seller: Taizhou Feike Mechanical Technology Co., Ltd. | FEIKE’s High Pressure Washer is designed for industrial cleaning, equipment maintenance, ve... |
 |
ER4043 Silicon Aluminum Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin... |
 |
HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line | Seller: Shandong HUASU Plastic Technology Co.,Ltd. | The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi... |
