Hydraulic Pump Contamination Resistance Tester
Hydraulic pump pollution resistance test bench is mainly used to detect the fuel pump in the specified concentration of pollution in the operating medium when the fuel pump to withstand the characteristics of pollution.
Test Object:
Fuel Pump
Test Item:
Fuel Pump Pollution Resistance Test
Technical Parameters:
1. Test oil: RP-3 aviation kerosene
2. Test powder: in accordance with the provisions of Table II of GJB.1003.1996.
3. Medium temperature: 10-40 ° C
4. Purification cleanliness: -/12/10 (GB/T
5. Test flow: 150 ~ 750L / min (fuel pump J / RLB-160; fuel pump J / RLB155-011); 250 ~ 1150L / min (fuel pump J / RLB-162).
6. Test pressure: 0 ~ 1MPa
7. Fuel tank volume: 1000L
8. Equipment power supply: AC 380V / 50Hz
9. Equipment power: 25kW
10. External dimensions: 5000 × 200 × 2000 (L × W × H) (subject to measurement)
11. Weight: 1000kg
Range of variation of instrument accuracy and test conditions:
1. Pressure kPa: 0.5% FS
2. Flow rate L/min: 0.5%FS
3.Temperature ℃: Class A
Main structure description:
(1) Stirring oil tank, working oil tank with conical oil tank, stirring oil tank installed inside the agitator
(2) Circulation pump circulates stirring and cooling; oil is discharged from the working oil tank.
(3) Bypass circulation purification
(4) pump casing fixed in the working tank box, the working tank box below the installation of the oil plate
(5) two sets of flow measurement devices through the manual switching valve conversion
Send product request
Other supplier products
 |
Gelbo Flex flexing chamber | Gelbo Flex flexing chamber is designed to measure the amount of fiber debris of non-woven fabrics in the dry state in accordance with ISO9073-10. I... |
 |
Mask Tensile Testing Machine ISO13934-1 ISO13934-2 | Mask Tensile Testing Machine： The electrical part consists of a load measuring system and a deformation measuring system. All control parameters a... |
 |
Electric notch machine | Plastic electric notch prototype is a cantilever beam, simply supported beam impact testing machine to do the impact toughness test of non-metallic... |
 |
Floor Material Burning Performance Tester | Standards: ASTM E648-15 Standard test method for critical radiant flux of floor-covering systems using radiant heat energy source BS EN ISO Rea... |
 |
Automatic open flash point tester | Product Introduction: The instrument can automatically test the flash point and ignition point of petroleum products （the ignition point of oil ex... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
