Rubber Mooney Viscosity Tester

Test principle:

The Mooney viscometer is used to measure the viscosity of rubber under specific conditions. In the test, the rubber sample was loaded into the mold cavity of the Mooney viscometer and the motor was started after preheating, and the rotor began to rotate and a certain shear torque was applied. At the same time, the rubber sample produces an equal and opposite resistance moment, which is displayed by the dial indicator installed at one end of the worm or directly through the computer, that is, the Mooney viscosity value.

Reference standard:

GB/T 1232 unvulcanized rubber - Determination of Mooney viscosity

GB/T 1233 rubber compound -- Determination of initial vulcanization characteristics -- Mooney viscometer method

HG-T 3242-2017 Rubber Mooney viscometer

ISO289 unvulcanized rubber -- determination by shear disc viscometer

ISO667 rubber compound - Determination of initial vulcanization characteristics - Mooney viscometer method

Technical parameters:

Measurement and control temperature range: normal temperature ——200℃

Torque measuring range: 0-100 Mooney value

Calibration accuracy: 100±0.5 Mooney value

Rotor speed: 2±0.02 RPM

Measurement time: 0-200 points

Ambient temperature: 0-35℃

Relative humidity: <80%

Test pressure: 11.5KN±0.5KN

Air pressure: 0.45-0.6MPa

Test requirements:

1） Scope: This specification specifies the test method of Mooney viscosity of rubber compound.

Note: Measuring range includes: Mooney viscosity.

2） Test tools: Mooney viscometer, electronic scale, scissors, heat insulation gloves

3） Sample requirements: Cut two rubber samples with a diameter of about 45mm and a thickness of about 3mm from the bubble-free rubber material, one of which has a circular hole with a diameter of about 8mm in the center of the sample （two pieces of rubber material weigh about 16g）。

4） Test conditions: the rubber material can be tested for more than 2 hours under laboratory conditions after processing, but not more than 10 days.

Other supplier products

	Negative pressure tester for medical syringes	Negative pressure tester for medical syringes - Other test instrument - standard Product Information: Instrument characteristics 　　It is compo...
	Protective Clothing Liquid Static Pressure Tester	Instrument use: The acid-proof clothing material anti-seepage acid static acid pressure tester is used to measure the acid-base anti-seepage of br...
	Bone Cement Four-Point Bending Fatigue Tester	Standard YY/T 1429 (China): Specifies four-point bending fatigue tests for acrylic resin bone cements under quasi-static and cyclic loading. IS...
	textile spray rating tester ISO 4920 BS EN 24920	Standards: ISO 4920. BS EN 24920. BS 3702. GB/T 4745. AATCC 22. M+S P23. NEXT 23 Applications: Fabric surface waterproof performance tester to d...
	Schildknecht Flexing Tester ISO 7854 BS 3424	Standards: ISO 7854.BS 3424 Applications: Schildknecht Flexing Tester is designed to determine the resistance of coated fabrics to damage by fle...

All supplier products

Same products

	Air Permeability Tester STD- F8	Seller: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Seller: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Seller: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Seller: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Seller: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...