GAS Combustion Rate Tester,ISO817,Testing Machine

Introduction

The combustible gas combustion rate tester is developed in accordance with the requirements of UL9540A and accordingtothestandardofAppendixCofISO817.Thecombustionrateofcombustiblegasinaverticalglasstube and related auxiliary parameters are recorded by camera equipment to realize the measurement of combustible gas combustionrate.

Standard

ISO817

System composition

The combustible gas combustion rate tester is mainly composed of combustion tube, ignition system, camera, gas supply system and exhaust gas treatment system;

1.Combustiontube:

1.1It is made of quartz glass, with an inner diameter of 40mm and a length of1.2m;

1.2The combustion tube is placed vertically and fixed by machiningtooling;

1.3The opening at the bottom of the combustion tube is equipped with an ignition system and a damping hole;

1.4The top of the combustion tube is connected to the stirring vessel. The test gas flows in from the top and flows out from the bottom. The top should be closed before ignition and flame propagation areover;

1.5There are quenching nets installed at both ends of the pipe, and the mesh size is1mm;

2.Ignitionsystem:

2.1The ignition system is installed at the bottom of the combustiontube;

2.2The ignition electrode is made of tungsten with a diameter of 1mm, inserted on both sides of the bottom, with a distance of6.4mm;

2.3Ignition transformer output 15kV,30mA;

2.4The ignition time can be edited, the default is0.3±0.05s;

3.Camera

3.1Use a high-speed industrial camera system to record the flame spreadingprocess;

3.2Equipped with camera mounting bracket, the height can beadjusted;

3.3A reflector is installed on the side of the combustion tube, so that the camera can capture the effects of frontal and side flames at the same time;

3.4The dedicated flame graph analysis software calculates the flame height.

4.Gas supplysystem

4.1The air supply system consists of a suction pump and a flowmeter;

4.2Imported KNF suction pump with a flow rate of33L/min;

4.3Stable input of the sample gas flow through the flowmeter;

4.4Configure a mixing container and a magnetic stirrer to make the test sample gas evenlymixed;

4.5Purge with air before the test to remove impurities in the combustiontube.

Other supplier products

	Protective Clothing Flame Spread Test Machine	The tester is used for flame spread test of protective clothing. It is designed and manufactured according to ISO 15025 Standard for Protective Clo...
	Fiber Blend Ratio Tester	The Fiber Blend Ratio Tester is designed to measure the electrical resistance of a compacted fiber sample and convert it into the specific resistan...
	Thin Film Pendulum Impact Tester	Main Uses of the Film Pendulum Impact Tester The film pendulum impact tester is mainly used to determine the resistance to pendulum impact of mate...
	Bio-absorbable Internal Fixation Plates and Screws Tester	Standard YY/T 0509-2009 (China): Specifies mechanical testing protocols for orthopedic plates/screws made of hydrolyzable polymers, including axia...
	Surgical Mask Flame Retardant Tester	The Surgical Mask Flame Retardant Tester is designed to evaluate the flame-retardant performance of surgical masks. In the event that a mask is acc...

All supplier products

Same products

	Lithium battery explosion test chamber,IEC 60086,UL 913	Seller: Standard International Group (HK) Limited	Lithium battery combustion and explosion experiment chamber is mainly used for thermal runaway co...
	STD Lithium battery explosion test chamber,Testing Machine	Seller: Standard International Group (HK) Limited	Introduction Lithium battery combustion and explosion experiment chamber is mainly used for ther...
	GAS Combustion Rate Tester,ISO817,Testing Machine	Seller: Standard International Group (HK) Limited	Introduction The combustible gas combustion rate tester is developed in accordance with the requ...
	Flammabillity Test Machine,BSS 7230 ,FAA.FAR.25.853	Seller: Standard International Group (HK) Limited	Introduction The product is according to aviation standards FAR-25 Appendix F of the first part ...
	Smoke Density Chamber (Horizontal Test),Smoke density evaluation device,ISO 5659	Seller: Standard International Group (HK) Limited	The main principle is to measure smoke density in a particular space, cable or material produced ...