Fogging tester

Brief Introduction:
The fogging tester used to test the properties under certain environmental conditions for leather and fabric fogging phenomenon, for the automotive, aircraft and other interior materials fogging performance at high temperatures volatile components of its evaluation, may be applied to the vehicle in front xenon lamp Determination of fogging properties.
Product Description:
It applies to the following test methods:
1) Gloss Method: the sample cup is heated by the fog evaporated gas condensing on cold glass by glass gloss values were compared before and after condensation and calculated, the sample can be drawn into the fog value.
2) Gravimetric method: the sample cup is heated by the fog evaporated gas condensing on cold aluminum foil, aluminum foil condensed by weighing before and after the change in weight, the sample can be drawn from the atomization - the weight of condensate.
3) Haze method: the sample cup is heated by the fog evaporated gas condensing on cold glass, through the haze value before and after the glass condensate compare and calculate, the sample can be drawn into the fog value.
Technical Parameter:
Hot bath temperature range: room temperature ~ 150 ℃ (room temperature ~ 280 ℃ optional)
High-temperature tank temperature control accuracy: ± 0.1 ℃ (150 ℃)
Low bath temperature range: 0 ~ 100 ℃
Cold tank temperature control accuracy: ± 0.1 ℃
High temperature trough Dimensions: 670 mm (L) × 490 mm (B) × 540 mm (H)
Cryogenic tank Dimensions: 400 mm (L) × 220 mm (B) × 520 mm (H)
Temperature tank Weight: 32kg (not including the thermally conductive medium)
Cryogenic tank Weight: 15kg (not including the thermally conductive medium)
Power: AC 220V 50Hz
Weight: 50kg
Size: 500 * 650 * 600mm
Consumables:
Glass (square, circle);
Test plate frame;
Nebulizer cup;
Sampler;
Aluminum foil;
Filter paper;
Rubber ring 95 * 4;
DOP;
DIDP;
Silicone oil;
Other supplier products
|
|
N95 Face Mask Material Meltblown Nonwoven Fabric Particle Filtration Efficiency (PFE) Tester |
N95 Face Mask Material Meltblown Nonwoven Fabric Particle Filtration Efficiency (PFE) Tester
is applicable to the performance verification of new ... |
|
|
digital fabric elmendorf tearing strength tester |
Standards: ASTM D1424/D689, NEXT 17, M&S P29, BE EN ISO 13937/4674, BS 4468, DIN EN 21974, GB/T 3917.1, ISO 1974 Applications: Digital Elmendo... |
|
|
Medical Mask Synthetic Blood Penetration Tester |
Surgical Masks Synthetic Blood Penetration Resistance TesterMedical Face Mask Synthetic Blood Penetration Resistance Tester is mainly used in the b... |
|
|
Fabric Heat Conduction Performance Tester |
标准:
EN 367-1992?防护服-防热和防火-测试方法:测定暴露于火焰时的热传递率
应用:
产品信息:
该仪器主要用于纺织品、消防用品等材料热导率的测定。特点: ◆仪器能数字显示火焰温度、测量温度、时间。◆燃烧器配有适用于燃烧石油液化气的火焰喷嘴,气孔分布... |
|
|
textile sublimation color fastness tester |
Testing Standards:
ISO 105 X11/P01, BS 1006, AATCC 92/114/117/133, GB/T 5718/6152, DIN 54022/54060, JIS L0879/L0850
Applications:
Scorch/Sublima... |
All supplier products
Same products