Removable Flask Molding Machine, Sand Molding Machine

• 

removable flask molding machine with its production of core more complex castings and sand line simple, less investment, occupies a small area and has a high degree of automation, high production efficiency, easy to operate, easy to get off the core, molding and pouring process is good, for casting sand automatic molding, high efficiency, stable quality, simple operation.

The hydraulic system is controlled by the proportional valve of Taiwan Seven Oceans, with the high-resolution electronic ruler for real-time tracking and positioning of the actuator, so that the adjustment of system pressure and flow can be precisely realized on the touch screen.

characteristics of removable flask molding machine:
1.Automatic one-button operation, easy to understand, easy to operate, no need for professional workers.
Each complete molding only needs to press the start button once (without core working condition), such as the workpiece that needs to be under core, the program will stop automatically after selection, after the core is completed, press the close mold button, the program is completed automatically.
2. Horizontal parting, vertical parting, no column blocking, easy to lower the core.
3. Template installation: four screws fixed, replaced within five minutes, adapt to replace the same size mold.
4. Casting hardness: Casting hardness can be freely adjusted according to the requirements of different castings, only a few parameters to adjust very convenient and rapid, up to 85-90 degrees.
5. Casting height adjustable, saving sand: the upper and lower compaction plates are adjustable, thus producing different casting heights.
6. Moulding accuracy: moulding and moulding are carried out in the uniformly positioned mould board and sand box system, with high repeatability. The whole molding process is fully automatic control, without human factors interference, so the molding quality is stable and efficient.
7. Casting quality is constant and uniform: this machine adopts high-precision mechanical positioning system, microcomputer and position detection linkage, the whole molding process is fully automatic control, without human factors interference, so the molding quality is stable and reliable.
8. With safety protection device: advanced light curtain protection, to ensure the personal safety of the operator.
9. Modeling speed: about 40 seconds per box; touch screen, parameter setting, very convenient, can be customized according to customer requirements for large-size models.
10. It can be equipped with conveying line or single machine production. This machine can be produced without very complicated wiring, customers can use the original sand mixer, and then equipped with a conveying belt to the sand addition port of this machine to realize fully automatic production.
11. There are as many as 100-150 reserved positions for gates and air pins, which makes it easy to design the gates and solve the air permeability problem and improve the yield of castings.

Other supplier products

	S99 Magnetic Separator	S99 series permanent magnet separation equipment, using high magnetic material, has strong magnetic strength. It is widely used in metallurgy, mini...
	S43 Riddle	Large end feeding and small end discharging (spindle tilting installation) are adopted to improve the screening ability. Due to the high speed, the...
	Sk Series Three-Dimensional Vibrating Table	The three-dimensional vibrating table is usually excited by 6 sets (3 groups) of vibration motors. When the dual motors rotate in the opposite dire...
	Vertical Parting Boxless Molding Machine, Sand Molding Machine	Vertical parting boxless molding machine is suitable for mass production of small and medium-sized cast iron parts (gray cast iron, malleable cast ...
	Green Sand Molding Line	Green sand (green sand) sand recovery system can be customized according to the casting productClay sand is the molding sand with clay as the binde...

Same products

	METAL BRACKETS	Seller: JCL Precision Part Co.Ltd.	Custom metal brackets are some of the strongest supports. JCL precision-engineers them to your cu...
	Ceramic Core Injector	Seller: Qinhuangdao Aifu Science & Technology Co., Ltd.	The Ceramic Core Injector is designedspecifically for producingcomplex, high quality and high pre...
	Wax Injection Machine	Seller: Qinhuangdao Aifu Science & Technology Co., Ltd.	The Wax Injection Machine is used to make wax patterns in the investment casting process with mid...
	Automatic Dewaxing Autoclave	Seller: Qinhuangdao Aifu Science & Technology Co., Ltd.	Dewaxing Autoclave is specially designed for removing the wax patterns in the ceramic shell. Ins...
	CNC TURNING	Seller: Baoji Haiqiao Industrial & Trading Co., Ltd.	As a CNC turning manufacturerin China, HQ has the capacity to dealing with both small lot and mas...