Thermal Protective Performance Tester (TPP)
The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.
Standards：
BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306
Feature：
Industrial personal computer with analysis software is suitable for severe testing conditions.
Automatic calculation for heat transmission factor and radiant heat transfer index.
Sample holder with force applied kit is easy to operate.
Single pump for shutter movement and cooling water loop.
TPP Specifications：
• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size
• Copper slug calorimeter sensors (ASTM or ISO)
• ± 0.75°C temperature measurement
• ± 3% radiant heat flux measurement
• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)
• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)
• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase
• Maximum nominal current 20 Amps
• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)
• Cooling Water: Cooling water required, chiller or tap water source is acceptable
• Propane Requirement: Regulated supply at 15 PSI (minimum)
• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps
• Two gas burners with flame detection auto ignition
• Mass flow controller for precise gas control
• Water-cooled protective shutter
• Pneumatic sample carriage and shutter assembly
• Integrated sensor cooling stand (air cooled)
• Emergency stop cuts gas flow, power to lamps and pneumatics
• Tinted tempered glass shield protects operator
• Software safety interlocks monitor water flow, carriage position, burner ignition
Send product request
Other supplier products
 |
UV Lamp Aging Test Tester | This product uses fluorescent UV lamps, combined with temperature and humidity device to simulate the material decline in color, brightness, streng... |
 |
Thermal Conductivity tester Of High Temperature Materials | Product details The high temperature thermal conductivity tester is a test instrument prepared according to GB / T17911-2006. YB / T 4130-2005 sta... |
 |
Gas Hazardous Characteristics Tester | Product Introduction This tester is used to test the flammable concentration range of gases in air. It is suitable for the vast majority of pure f... |
 |
Safety Helmets Acceleration Impact & Penetration Tester | Standard GB/T 2812: Safety Helmets (China National Standard) Equivalent Compliance: ISO 6220-1 (Industrial Safety Helmets – Impact Absorpti... |
 |
Building Material Smoke Density Testing machine | Product details In the event of fire, people are choked by smoke or can not escape because they can not see the road. Therefore, in the prevention... |
Same products
 |
Custom Stainless Components for OEM Applications | Seller: Yongjia County Yaokang Technology Co., Ltd. | Our stainless steel float balls are designed for float valves, water tanks, and industrial liquid... |
 |
Precision Design for Automatic Liquid Level Control | Seller: Yongjia County Yaokang Technology Co., Ltd. | Our stainless steel float balls are designed for liquid level control applications in valves, tan... |
 |
"China manufacturer power supply VM-5H3 for power generation | Seller: DONGFANG YOYIK (DEYANG) ENGNIEERING CO; LTD | "China manufacturer power supply VM-5H3 for power generation Is to use the generator sets of prof... |
 |
Reliable Components for Water and Industrial Systems | Seller: Yongjia County Yaokang Technology Co., Ltd. | The Stainless Steel Float Ball is designed for automatic liquid level control and fluid managem... |
 |
Double Convex Lenses | Seller: Shandong Yanggu Constant Crystal Optics, Inc | Double Convex Lensesare used in image relay applications, or for imaging objects at close conjuga... |
