Titanium Sapphire Laser Crystals
DescriptionTi:sapphire (Titanium doped Sapphire,Website:, Al2O3:Ti3+) is used for making ultra short pulse solid-state or wavelength tunable lasers.Ti:sapphire lasers are also very convenient e.g. for pumping test setups of new solid-state lasers (e.g. based onneodymium-orytterbium-doped gain media), since they can easily be tuned to the required pump wavelength and allow one to work with very high pumpbrightnessdue to their goodbeam qualityand high output power of typically several watts. Features:Best materials for ultrashor pulse generationTunable range from 600-1100nmHigh gainCould be pumped by shor pulse flash lampsGood physical and optical properties
Properties of Ti:sapphireSapphire (monocrystalline Al2O3) has an excellent thermal conductivity, alleviating thermal effects even for high laser powers and intensities.The Ti3+ion has a very largegain bandwidth(much larger than that ofrare-earth-doped gain media), allowing the generation of very short pulses and also widewavelength tunability(typically using abirefringent tuner). The maximum gain and laser efficiency are obtained around 800nm. The possible tuning range is ≈ 650nm to 1100nm, but different mirror sets are normally required for covering this huge range, and exchanging mirror sets is a tedious task. (The number of mirror sets required can be reduced by using ultrabroadbandchirped mirrors.)There is also a wide range of possible pump wavelengths, which however are located in thegreenspectral region, where powerfullaser diodesare not available. In most cases, several watts of pump power are used, sometimes even 20W. Originally, Ti:sapphire lasers were in most cases pumped with 514-nmargon ion lasers, which are powerful, but very inefficient, expensive to operate, and bulky. Other kinds ofgreen lasersare now available, andfrequency-doubledsolid-state lasersbased onneodymium-doped gain mediaare widely used. The pump wavelength is then typically 532nm, with a slightly reducedpump absorptionefficiency compared with 514nm.Theupper-state lifetimeof Ti:sapphire is short (3.2μs), and thesaturation poweris very high. This means that the pump intensity needs to be high, so that a strongly focused pump beam and thus a pump source with highbeam qualityis required.Despite the huge emission bandwidth, Ti:sapphire has relatively high lasercross sections, which reduces the tendency of Ti:sapphire lasers forQ-switching instabilities.EndFragmentApplications:Laser spectroscopyLIDARsMedial laser
Meta-Photonics Ti:sapphireGrown by Thermal Exchange Method
Figure of Merit (FOM) value: 150-350Absorption coefficient:0.3~3.5cm-1;Maximal Size: dia150mmCustom design prouction (special doping concentration, shape, coating) is availableSpecificationParameters of materialsMaterialsTi3+:Al2O3Concentrations(0.05~0.35)wt%Ti2O3OrientationA-Axis within 5°,E-vector parallel to C-AxisEnd Configurationflat/flat or Brewster/Brewster endsAbsorption Coefficence0.5～6.0cm-1Figure of Merit100~300CoatingsStandard coating is BBAR with R < 5.0% each face at 532 nm and R < 0.5% each face, 650 nm to 850 nm.Other coatings available.Polishing Specification for Laser GradeOrientation Tolerence< 0.5°Thickness/Diameter Tolerance±0.05mmSurface Flatness<λ/8@632nmWavefront Distortion<λ/4@632nmSurface Quality10/5Parallel30〞Perpendicular15ˊClear Aperture>90%Chammfer<0.2×45°Standard productsAperture dimensions,mmlength,mmEnd surfaceCoatingsFOMProduct IDPricedia65 €Brewster Cut->120 10 €>150 15 €>150 20 €>180 5 €Right-angle Cut(R<1%)@532 nm + (R<0.3%)780-820 nm>120 10 €>150 15 €>150 20 €>180 6x65 €Brewster Cut->120 10 €>150 15 €>150 20 €>180 5 €Right-angle Cut(R<1%)@532 nm + (R<0.3%)780-820 nm>120 10 €>150 15 €>150 20 €>180
Other supplier products
|
|
PbMoO4 Acousto Optical Crystals |
PbMoO4 acousto-optic crystalsLead Molybdate (PbMoO4 or PM) crystal is one of the most efficient materials used for acousto-optic devices. It has be... |
|
|
MgF2 Optical Crystals |
MgF2 optical crystalsMagnesium Fluoride (MgF2) is commonly used for UV windows,Website:, lenses and polarisers. It is also useful in its transmissi... |
|
|
Ce LuAG Scintillation Detector |
DescriptionLuAG:Ce,Website:, Lutetium Aluminum Garnet activated by cerium (chemical formula Lu3Al5O12), is a relatively dense and fast scintillatio... |
|
|
ZnO Crystal Substrates |
DescriptionZinc Oxide (ZnO) can be grown as a single crystal semiconductor with very interesting properties. The bandgap is in the 3.4 eV range whi... |
|
|
GGG Laser Crystals |
Doped GGG (Gd3Ga5O12) laser crystalsNew laser crystals using GGG (Gd3Ga5O12) as host could be growth for scientificresearch.
Doping ions: Nd,Webs... |
All supplier products
Same products
