Hypertherm Plasma Consumables 120792 , Plasma Cutter Swril Ring

• 

Hypertherm HT4400 Swril Ring 120792, Plasma Cutter Swril Ring ,Plasma Machine Swirl Ring

FAQ:

Q1:Can I get a free samples to check the quality?

A:Sure,we can supply the free samples but you need bear the express cost by yourself.

Q2:Will I afford the carrier charge?

A:Yes,you will afford the express charge or your account is OK.

Q3:Can I add my trademark on my products?

A:Yes,we need your certificate of authorization.

Technical Support:
A

Plasma cutting machine matters needing attention

The selection of cutting parameters of CNC plasma cutting machine is very important for cutting quality, cutting speed and efficiency. The correct use of CNC plasma machine for high quality fast cutting, cutting process parameters must be deeply understood and mastered.

First, cutting current: it is the most important cutting process parameters, directly determines the cutting thickness and speed, that is, cutting ability. Effects: 1, cutting current increases, an increase in the energy of the arc, cutting ability, the cutting speed is increased; 2, cutting current increases, increasing the diameter of the arc arc variable rough makes incision width; 3, cutting current ambassador to the nozzle increases the heat load, the nozzle premature damage, cutting quality of the natural decline, can't even normal cut. So the cutting current and the corresponding nozzle should be chosen according to the thickness of the material before cutting.

Second, cutting speed: best cutting speed range according to equipment illustrate selected or test to determine, due to the thickness of the material, different materials, high melting point, thermal conductivity and melting the surface tension and other factors, the cutting speed is also a corresponding change. The main performance: 1, cutting speed can be improved to improve the quality of the cut, that is slightly narrow incision, incision surface more smooth, and can reduce the deformation. 2, the cutting speed is too fast that cutting line energy lower than the required value, cut seam in the jet can't quickly melted cutting melt immediately blew and the formation of larger drag, accompanied by incision slag hanging, the surface quality of the incision down. 3, when the cutting speed is too low, because the cut is plasma arc anode, in order to maintain the stability of the arc's, anode spot or anode region must from recent arc cutting seam found near the conduction current place, at the same time will pass more heat to a radial jet, so make the incision became wide, on both sides of the notch of molten material in the bottom flange aggregation and coagulation, form is not easy to clean the slag hanging, and incision margin due to excessive heating and melting and the formation of fillet. 4, when the speed is very low, because the cut is too wide, the arc will even put out. It can be seen that good cutting quality and cutting speed can not be separated.

Другие товары поставщика

	Hypertherm ArcWriter Plasma Cutting Electrode 120447 For Hypertherm Plasma Consumables	We are specialized in the production of plasma cutting machine torch consumables manufacturer, we are engaged in the industry for ten years. Our pr...
	Plasma Electrode 220842, Hypertherm Powermax 105 Consumables For PowerMax105 / PowerMax85	Hypertherm Plasma Electrode 220842 Plasma Consumables For PowerMax105 / PowerMax85 We can offer you all plasma consumables for hyptertherm, ...
	Silver Electrode 220971 Hypertherm PowerMax 125 Consumables for PowerMax125	Hypertherm Silver Electrode 220971 Plasma Cutting Consumables for PowerMax125 We are specialized in the production of plasma cutting machine...
	Hypertherm Plasma Consumables 120792 , Plasma Cutter Swril Ring	Hypertherm HT4400 Swril Ring 120792, Plasma Cutter Swril Ring ,Plasma Machine Swirl Ring FAQ: Q1:Can I get a free samples to check the quality? ...
	220798 Shield For PM65/85/105, Professional Hypertherm Powermax Consumables	Machine HEC NO. Ref NO. Description HPR 130 HPR 260 HPR 130XD HPR 260XD HPR 400XD H03192 220192 Ele...

Похожие товары

	HEX NUTS	Продавец: Chenglong Technology(Jiaxing) Co.,Ltd.	Our Hex Nuts are designed for dependable fastening performance across a wide range of industrial,...
	7123340M	Продавец: 864106	Mary from China-Lutong Head Rotor 7123340M 7123340R 7123340S 7123340U 7123340W Whats/ app:+...
	10mm pump head	Продавец: 864106	来自中国的玛丽-鲁通 10mm泵头、11mm泵头组件、11mm泵头出售、11mm泵头套件、11mm泵头套件出售 什么/应用程序：+8–6–1–3&ndas...
	Magnetic Handbag Buttons	Продавец: Wenzhou Wiko Garments Accessories Co., Ltd	Magnetic handbag buttons, available in thick and thin styles, suitable for all kinds of handbags....
	Leather Toggle Button for Coats	Продавец: Wenzhou Wiko Garments Accessories Co., Ltd	The raw materials of genuineleather coat toggle buttonsare made from artificially raised cowhide ...