Finecut consumable, Air Plasma Nozzle 220930, PMX Air Plasma Cut
Finecut consumable, Air Plasma Nozzle 220930, PMX Air Plasma Cut
An electrical arc is then formed within the gas, between an electrode near or integrated into the gas nozzle and the work piece itself. The electrical arc ionizes some of the gas, thereby creating an electrically conductive channel of plasma. As electricity from the cutter torch travels down this plasma it delivers sufficient heat to melt through the work piece. At the same time, much of the high velocity plasma and compressed gas blow the hot molten metal away, thereby separating i.e. cutting through the work piece.
Plasma cutting is an effective means of cutting thin and thick materials alike. Hand-held torches can usually cut up to38mm thick steel plate, and stronger computer-controlled torches can cut steel up to 150 mm thick.[1] Since plasma cutters produce a very hot and very localized "cone" to cut with, they are extremely useful for cutting sheet metal in curved or angled shapes.
Machine | HEC NO. | Ref NO. | Description |
|
H03192 | 220192 | Electrode,30Amp |
H03552 | 220552 | Electrode,50Amp | |
H03187 | 220187 | Electrode,80Amp | |
H03181 | 220181 | Electrode,130Amp | |
H03352 | 220352 | Electrode,200Amp | |
H03435 | 220435 | Electrode,260Amp | |
H03649 | 220649 | Electrode,130Amp Bevel | |
H03541 | 220541 | Electrode,260Amp Bevel | |
H03665 | 220665 | Electrode,130Amp(silver Plus) | |
H03666 | 220666 | Electrode,200Amp(silver Plus) | |
H03668 | 220668 | Electrode,260Amp(silver Plus) | |
H03629 | 220629 | Electrode,400Amp | |
H73180 | 220180 | Swirl Ring,30Amp | |
H73553 | 220553 | Swirl Ring,50Amp | |
H73353 | 220353 | Swirl Ring,200Amp | |
H73179 | 220179 | Swirl Ring,80/130/260Amp(Bevel) | |
H73436 | 220436 | Swirl Ring,260/260Amp(Bevel) | |
H73631 | 220631 | Swirl Ring,400/400Amp(Bevel) | |
H13193 | 220193 | Nozzle,30Amp | |
H13554 | 220554 | Nozzle,50Amp | |
H13188 | 220188 | Nozzle,80Amp | |
H13182 | 220182 | Nozzle,130Amp | |
H13354 | 220354 | Nozzle,200Amp | |
H13439 | 220439 | Nozzle,260Amp | |
H13646 | 220646 | Nozzle,130Amp(Bevel) | |
H13542 | 220542 | Nozzle,260Amp(Bevel) | |
H13632 | 220632 | Nozzle,400/400Amp(Bevel) | |
H33754 | 220754 | Retaining Cap 30/50Amp | |
H33176 | 220176 | Retaining Cap 80/130Amp | |
H33355 | 220355 | Retaining Cap 200Amp | |
H33433 | 220433 | Retaining Cap 260Amp | |
H33603 | 220603 | Retaining Cap (Bevel) 130/260Amp | |
H33756 | 220756 | Retaining Cap 80/130Amp | |
H33757 | 220757 | Retaining Cap 200Amp | |
H33760 | 220760 | Retaining Cap 260Amp | |
H33635 | 220635 | Retaining Cap 400/400Amp(Bevel) | |
H33740 | 220740 | Retaining Cap (Bevel) 130/260Amp | |
H23194 | 220194 | Shield,30Amp | |
H23555 | 220555 | Shield,50Amp | |
H23189 | 220189 | Shield,80Amp | |
H23183 | 220183 | Shield,130Amp | |
H23356 | 220356 | Shield,200Amp | |
H23440 | 220440 | Shield,260Amp | |
H23645 | 220645 | Shield,130Amp(Bevel) | |
H23545 | 220545 | Shield,260Amp(Bevel) | |
H23761 | 220761 | Shield,200Amp | |
H23764 | 220764 | Shield,260Amp | |
H23636 | 220636 | Shield,400/400Amp(Bevel) | |
H23742 | 220742 | Shield,130Amp(Bevel) | |
H23741 | 220741 | Shield,260Amp(Bevel) | |
H43173 | 220173 | Retaining Cap 30/50/80/130Amp | |
H43398 | 220398 | Retaining Cap 200/260/(Bevel)130/260Amp | |
H43747 | 220747 | Retaining Cap 30/50/80/130Amp | |
H43637 | 220637 | Retaining Cap 200/260/400Amp(Bevel) | |
H83818 | 128818 | HPR torch assembly | |
H83162 | 220162 | Quick-disconnect torch | |
H83163 | 220163 | Quick-disconnect recepticle | |
H83706 | 220706 | Quick-disconnect torch | |
H83705 | 220705 | Quick-disconnect recepticle | |
H93571 | 220571 | Water Tube with O-Ring | |
H93340 | 220340 | Water Tube with O-Ring(30/50/80/130/200/260Amp) | |
H93700 | 220700 | Bevel water tube(mild steel-130A) |
Technical Support:
Common problems in the application of plasma cutting machine
1, high pressure
"If the input air pressure far exceed 0.45MPa, after the formation of the plasma arc, the large flow of air will blow concentrated arc column, the energy of arc column dispersion, decreased the plasma arc cutting intensity. Cause the pressure is too high, the reasons are: improper input air conditioning, air filter regulator is too high or air filter valve failure.
The solution is to check whether the pressure of the air compressor is adjusted properly, air compressor and air filter pressure relief valve is dysfunctional. After startup, such as rotating air filter relief pressure valve adjusting switch, gauge unchanged, indicating that the air filter relief pressure valve failure, need to be replaced.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
Plasma Electrode 220842, Hypertherm Powermax 105 Consumables For PowerMax105 / PowerMax85 | Hypertherm Plasma Electrode 220842 Plasma Consumables For PowerMax105 / PowerMax85 We can offer you all plasma consumables for hyptertherm, ... | |
Plasma Electrode 220777, Hypertherm Powermax 105 Consumables For PowerMax105 Plasma Machine | Hypertehr Electrode 220777 Plasma Consumables For Hypertherm PowerMax105 plasma Machine We can offer you all plasma consumables for hypterth... | |
Hypertherm Plasma Cutting Electrode 220971 For PowerMax125 Plasma Cutter Parts | Hypertherm Plasma Electrode 220971 Plasma Torch Consumables for PowerMax125 We are specialized in the production of plasma cutting machine ... | |
Finecut consumable, Air Plasma Nozzle 220930, PMX Air Plasma Cut | Finecut consumable, Air Plasma Nozzle 220930, PMX Air Plasma Cut An electrical arc is then formed within the gas, between an electrode near or int... | |
Hypertherm Plasma Consumables 120792 , Plasma Cutter Swril Ring | Hypertherm HT4400 Swril Ring 120792, Plasma Cutter Swril Ring ,Plasma Machine Swirl Ring FAQ: Q1:Can I get a free samples to check the quality? ... |
Похожие товары
Общий рельсовый инжектор | Продавец: 德艾普( xiamen) импорт и экспорт Co., Ltd. | Item: Diesel Fuel Injector Model No: MOQ: 1pc Material: SteelPackage Deta... | |
Nursing Pads Wholesale | Продавец: Winner Medical Co., Ltd | Not only do the wholesale breast nursing pads produced by Winner have a segmented absorption stru... | |
5Axis CNC Machining Parts | Продавец: Xin Pin Prototype Manufacturing Co.,LTD | High efficiency and exact precision. A technology accumulated by wisdom to shape from simple to c... | |
KE600A Series Closed Loop Vector Control VFD | Продавец: Shenzhen MICNO Electric Co., Ltd. | KE600A series is a closed loop vfddeveloped on the basic of KE300, with more powerful functions, ... | |
Types Of Cheap Custom High-quality Zipper Woobie Hoodie For Sale | Продавец: Yppromotion | As a professional zipper woobie hoodiemanufacturer, Yppromotion has various customized camouflage... |