AGM BATTERY

• 

The AGM battery refers to the absorbent glass mat battery or absorbed glass mat battery, whose design principle is to inject the required amount of electrolyte into the polar plates and separators with no free electrolyte. The negative polar plate is wet to improve the ability to absorb oxygen. In order to prevent the electrolyte from reducing, so the battery is sealed. For this, the absorbent glass mat battery is also called a "starved-electrolyte battery".

The Influence of Temperature on AGM absorbed glass mat batteries Storage

Absorbed glass mat battery uses pure sulfuric acid aqueous solution as electrolyte, and its density is 1.29-1.3lg/cm3. Most of it exists in the glass fiber membrane, while a part of the electrolyte is absorbed inside the polar plate. In order to provide a channel for the oxygen precipitated from the positive electrode to the negative electrode, it is necessary to keep 10% of the pores of the separator not occupied by the electrolyte, which is, the starved-electrolyte design. The pole group adopts a tight assembly method to make the pole plate fully contact the electrolyte. At the same time, in order to ensure the battery has sufficient service life, the polar plate should be designed to be thicker, and the positive grid alloy adopts a quaternary alloy.

When the agm absorbed glass mat batteries are charged, the internal gas recombination itself is an exothermic reaction, which causes the battery temperature to rise, the floating current increases, and the gas evolution increases, which promotes the battery temperature to rise higher, and the AGM batterystorage will decrease. The battery itself is a "starved-electrolyte battery", tightly assembled, and difficult to dissipate the internal heat. If the heat is not removed in time, it will cause a thermal runaway. If the voltage at the end of floating charge is too high, the ambient temperature around the battery will increase, which will increase the thermal runaway of the battery.

Every time the temperature rises by 1°C, the battery voltage drops by about 3mV, causing the floating current to rise and the temperature to further rise. If the temperature is above 50°C, the battery jar will deform. When the temperature is lower than -40℃, the valve-regulated lead-acid battery can still work normally, but the AGM storage will be reduced.

High-performance AGM Absorbed Glass Mat Battery for Sale

High-performance Power advanced AGM batteryshould have the following characteristics:

Performance characteristics of advanced AGM battery

The top rated agm batteriesis a starved-electrolyte battery, so the electrolyte is absorbed in the AGM separator, and there is no flowing electrolyte in the battery. As AGM adopts advanced AGM battery materials and design technology, water loss is small during use, thus, no water is added. At the same time, high-performance AGM batteries also have the following advantages:

Use characteristics:

Low self-discharge and long service life. AGM lead-acid batteries can generally be used for 3 to 5 years. The grid of ordinary batteries is a lead-antimony alloy. During the charge-discharge cycles, antimony is transferred from the grid to the active material and electrolyte of the positive and negative electrodes, thereby increasing the battery’s self-discharge and shortening the service life of the battery. The absorbed glass mat battery for saleadopts lead-calcium alloy, and the alloy does not contain antimony, so the self-discharge can be reduced to a minimum and the service life of the battery is extended. Absorbent glass mat battery has high starting power. Compared with ordinary flooded batteries, due to the use of new materials and new design methods, its internal resistance is small, the output voltage is high, the low temperature starting current is large, and its service life is long.

KIJO is a leading AGM battery manufacturer/supplier/agm battery factoryin China, please contact us!

KIJO battery Group is a professionalstorage battery factory, we provide reserve power battery, flooded lead acid battery vs agm, agm battery dry out, agm storageand etc. Want to know where to buy agm deep cycle batteriesor more? Please contact us.

Другие товары поставщика

	BACKUP BATTERY SUPPLY SYSTEM	The rechargeable backup power supplyis also called an emergency power supply. It is a device that replaces the main power supply to supply power t...
	25.2V Lithium ion Battery	Founded in 1993, KIJO batteryGroup is a professional storage battery manufacturerintegrating science, industry and trade. KIJO has a production cap...
	12.8V Lithium ion Battery	KIJOprovides customers with china storage batterysuch as reserve power battery. Contact us to buy 12.8V lithium ion battery, 12ah lithium battery...
	KIJO RECHARGEABLE STORAGE BATTERY	KIJO is engaged in manufacturing different types of rechargeable batteries in China: Energy rechargeable storage battery, reserve power battery, mo...
	25.2V Lithium ion Battery	Specification of 25.2 v lithium ion battery Battery Model Rate Voltage（V） Rate Capacity（AH/10Hr) Dimension(mm) Weigh...

Похожие товары

	CSD16301Q2 TRANSISTOR MOSFET N-CH 25V 6SON TEXAS INSTRUMENTS	Продавец: ZK Electronic Technology Co., Limited	Part Number:CSD16301Q2 Description:CSD16301Q2 TRANSISTOR MOSFET N-CH 25V 6SON TEXAS INSTRUMENTS ...
	Конденсатор EEF-CX0J101R PANASONIC SMD SPEC полимер 100UF 6,3v SMD LF	Продавец: ZK Electronic Technology Co., Limited	Part name:EEF-CX0J101R Description:CAPACITOR EEF-CX0J101R PANASONIC SMD SPEC POLYMER 100UF 6.3V ...
	Heavy Copper PCB Manufacturer	Продавец: Xinfeng Huihe Circuits Co., Ltd.	Heavy Copper PCB, pcb fabrication up to 12oz, large current, pcb circuitfabrication base material...
	8 Layer ENIG Half Hole Custom PCB	Продавец: Xinfeng Huihe Circuits Co., Ltd.	Number of layers: 8 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 4/3mil Inner lay...
	4 Layer ENIG Impedance Control Half Hole PCB Electric Circuit Board	Продавец: Xinfeng Huihe Circuits Co., Ltd.	Number of layers: 4 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 6/4mil Inner lay...