AGM BATTERY
The AGM battery refers to the absorbent glass mat battery or absorbed glass mat battery, whose design principle is to inject the required amount of electrolyte into the polar plates and separators with no free electrolyte. The negative polar plate is wet to improve the ability to absorb oxygen. In order to prevent the electrolyte from reducing, so the battery is sealed. For this, the absorbent glass mat battery is also called a "starved-electrolyte battery".
The Influence of Temperature on AGM absorbed glass mat batteries Storage
Absorbed glass mat battery uses pure sulfuric acid aqueous solution as electrolyte, and its density is 1.29-1.3lg/cm3. Most of it exists in the glass fiber membrane, while a part of the electrolyte is absorbed inside the polar plate. In order to provide a channel for the oxygen precipitated from the positive electrode to the negative electrode, it is necessary to keep 10% of the pores of the separator not occupied by the electrolyte, which is, the starved-electrolyte design. The pole group adopts a tight assembly method to make the pole plate fully contact the electrolyte. At the same time, in order to ensure the battery has sufficient service life, the polar plate should be designed to be thicker, and the positive grid alloy adopts a quaternary alloy.
When the agm absorbed glass mat batteries are charged, the internal gas recombination itself is an exothermic reaction, which causes the battery temperature to rise, the floating current increases, and the gas evolution increases, which promotes the battery temperature to rise higher, and the AGM batterystorage will decrease. The battery itself is a "starved-electrolyte battery", tightly assembled, and difficult to dissipate the internal heat. If the heat is not removed in time, it will cause a thermal runaway. If the voltage at the end of floating charge is too high, the ambient temperature around the battery will increase, which will increase the thermal runaway of the battery.
Every time the temperature rises by 1°C, the battery voltage drops by about 3mV, causing the floating current to rise and the temperature to further rise. If the temperature is above 50°C, the battery jar will deform. When the temperature is lower than -40℃, the valve-regulated lead-acid battery can still work normally, but the AGM storage will be reduced.
High-performance AGM Absorbed Glass Mat Battery for Sale
High-performance Power advanced AGM batteryshould have the following characteristics:
Performance characteristics of advanced AGM battery
The top rated agm batteriesis a starved-electrolyte battery, so the electrolyte is absorbed in the AGM separator, and there is no flowing electrolyte in the battery. As AGM adopts advanced AGM battery materials and design technology, water loss is small during use, thus, no water is added. At the same time, high-performance AGM batteries also have the following advantages:
Use characteristics:
Low self-discharge and long service life. AGM lead-acid batteries can generally be used for 3 to 5 years. The grid of ordinary batteries is a lead-antimony alloy. During the charge-discharge cycles, antimony is transferred from the grid to the active material and electrolyte of the positive and negative electrodes, thereby increasing the battery’s self-discharge and shortening the service life of the battery. The absorbed glass mat battery for saleadopts lead-calcium alloy, and the alloy does not contain antimony, so the self-discharge can be reduced to a minimum and the service life of the battery is extended. Absorbent glass mat battery has high starting power. Compared with ordinary flooded batteries, due to the use of new materials and new design methods, its internal resistance is small, the output voltage is high, the low temperature starting current is large, and its service life is long.
KIJO is a leading AGM battery manufacturer/supplier/agm battery factoryin China, please contact us!
KIJO battery Group is a professionalstorage battery factory, we provide reserve power battery, flooded lead acid battery vs agm, agm battery dry out, agm storageand etc. Want to know where to buy agm deep cycle batteriesor more? Please contact us.
在线联系供应商
Other supplier products
 |
24V Lithium ion Battery | KIJO Group is a professional storage battery companyin China, which is committed to offering better storage batterysolution to clients all over the... |
 |
LEAD CARBON BATTERY TECHNOLOGY | LEAD CARBON BATTERY TECHNOLOGY With the progress of society, the requirements for battery energy storage in various social occasions continue to i... |
 |
RESERVE POWER BATTERY | KIJO Group is a professional storage battery companyin China, which is committed to offering better battery solution to clients all over the world.... |
 |
GEL DEEP CYCLE BATTERY | Deep circulation gel cell is very common in various fields, and it mainly has the three types. Types of Deep Cycle Gel Batteries No free electro... |
 |
Hailong 36V Lithium Battery For Electric Bikes | Specification of 36 volt lithium ion battery for bikes Battery Model Rate Voltage（V） Rate Capacity（AH/10Hr) Dimension(mm)... |
Same products
 |
CSD16301Q2 TRANSISTOR MOSFET N-CH 25V 6SON TEXAS INSTRUMENTS | 卖方: ZK Electronic Technology Co., Limited | Part Number:CSD16301Q2 Description:CSD16301Q2 TRANSISTOR MOSFET N-CH 25V 6SON TEXAS INSTRUMENTS ... |
 |
CAPACITOR EEF-CX0J10CAPACITOR EEF-CX0J101R PANASONIC SMD SPEC POLYMER 100UF 6.3V SMD LF1R PANASONIC SMD SPEC POLYMER 100UF 6.3V SMD LF | 卖方: ZK Electronic Technology Co., Limited | Part name:EEF-CX0J101R Description:CAPACITOR EEF-CX0J101R PANASONIC SMD SPEC POLYMER 100UF 6.3V ... |
 |
Heavy Copper PCB Manufacturer | 卖方: Xinfeng Huihe Circuits Co., Ltd. | Heavy Copper PCB, pcb fabrication up to 12oz, large current, pcb circuitfabrication base material... |
 |
8 Layer ENIG Half Hole Custom PCB | 卖方: Xinfeng Huihe Circuits Co., Ltd. | Number of layers: 8 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 4/3mil Inner lay... |
 |
4 Layer ENIG Impedance Control Half Hole PCB Electric Circuit Board | 卖方: Xinfeng Huihe Circuits Co., Ltd. | Number of layers: 4 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 6/4mil Inner lay... |
