Fan Mold
If the weight of each fan blade is not balanced, large vibration, high noise, and large wear of the rotating shaft will occur during high-speed rotation, which not only seriously affects product performance, but also The lifetime will also be greatly reduced. Therefore, fan products must ensure that the weight of each fan blade is balanced in order to pass the detection of the dynamic balance detector and adapt to the working environment of such products.
High-quality Plastic Fan Mould
Fan blades are usually divided into shaft core circle, blade inner circle, and blade outer circle. If the concentricity of the shaft core circle, blade inner circle, and blade outer circle are not good, the fan blade will vibrate when it rotates, and the rotation will be unstable. Abnormal phenomena such as friction and noise occur around.
The mold core in the existing fan blade mold is square, and the inner hole in the middle of the square mold core can only be processed by wire cutting. The concentricity cannot be guaranteed, and the concentricity of the inner circle of the blade, the outer circle of the blade, and the shaft core circle cannot be guaranteed, so the quality of the product is not high enough.
Also, the injection fan blade mold must have high precision in centering the fan with the outside frame. GV Mold gives a special solution for the centering location, therefore, after the assembling, the plastic fan and the frame run without any noise of testing.
Basic Information for Fan Mold
Fan MoldSpecification
Description |
Fan Blade Plastic InjectionMold |
Plastic material |
ABS |
Mould dimension(mm) |
320*380*370 |
Mould weight (kg) |
200kg |
Mould cavity&core steel |
S136 |
Nos of Cavity |
1*1 |
Manufacture time (day) |
30 days |
Mould life |
≥300 000 |
Molding cycle (S) |
35s |
Mold Characteristics |
High concentricity requirements |
Short cycle time |
Design & Key Points for Plastic Fan Mold
The shape of the plastic fan blades is relatively simple. The first requirement is the principle of coincidence of the center of gravity. The size and thickness of all blades should be the same to ensure that the center of gravity of the product is located in the center of the plastic fan part. The second requirement is dynamic balance, that is, balance while rotating. These two requirements put forward higher requirements for the fan mold, that is, on the premise of ensuring the reasonable design of the mold, improving the mold manufacturing process, and improving the mold manufacturing quality.
In addition to paying attention to balance in the mold design process, the balance problem in mold processing is also important. The manufacture of mold cavity & core needs to be directly processed by a high-speed machine, and high-quality processing cutting tools are required. We should make sure each blade has the exact same shape and dimensional tolerances. After all machined, it should be inspected by 3-coordinate, and after all of the dimensions meet the tolerance, then fit the mold and assembly it.
We can provide kinds of injection molding dies for sale, if you have needs, please contact us.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
Aluminum Die Casting Mold | Aluminum High Pressure Die Casting Mold When working at high or low temperatures, they also maintain good mechanical properties and have good co... | |
Electronics Mold | Consumer electronics is very popular in our daily life. It consists of many different plastic parts, pcb boards, wires, battery and some metal part... | |
Teeth Tray Mold | A dental impression is a mold removed from a tooth to diagnose and treat dental conditions. They are also used in forensic science. Impressions are... | |
Plastic Spoon Mould | Plastic spoon mainly used for eating, so it need to be heat resistant and non-toxic,and could meet the requirements of environmental protectionso, ... | |
Keyboard Mould | Mainly electronic molds we make are electronic housing mold, electronic components mold, electronic dashboard cover mold, computer keyboard key mol... |
Похожие товары
Medical Plastic Parts | Продавец: Packson Mold Co.,Ltd | Project Management To be a qualified medical plastic components manufacturer, the most advanced ... | |
PA66 GF15 Heat Stabilized (A2006C, A2016C) for Engineering Plastics | Продавец: Suzhou Anmei Material Technology Co., Ltd | PA 66 GF 15is a 15% glass fiber reinforced, heat-resistance, polyamide 66 resin for injection mol... | |
PA66 GF | Продавец: Suzhou Anmei Material Technology Co., Ltd | Anmei focuses on the production of modified engineering plastics. We have polyamide pa6 6gfmodif... | |
Nylon6 PA6 | Продавец: Suzhou Anmei Material Technology Co., Ltd | Other than fiber-reinforced pa6 polyamide, the unreinforced nylon type 6 produced by Anmei, one o... | |
Nylon 66 Pa66 With High Tensile Strength (A2307X01, A2317X01) for Engineering Plastics | Продавец: Suzhou Anmei Material Technology Co., Ltd | Using Polyamide 66 as the basic resin, the tensile strength of nylon 66 is obtained by blending a... |