.

Pultruded Fiberglass Shapes

Cable trayis assembled by pultruded/FRP profiles;suitable for electrical cable, control cables, lightening cable and fittings. There are , fiberglass tank, fiberglass tube and vessel.

Advantage:

Application:

KQJ series cable tray is suitable for voltage below 10 kV electrical cables, control cable, and lightening fitting cables of below 10 kV and the lay out for indoor, outdoor, aerial, channel for cable and tunnel.

Structural features:

KQJ serial cable trays have the features that: widely used, high strength, reasonable structure, low cost, easy for construction, flexible fittings, nice-looking appearance, which make expansion, rebuilding, maintenance much easier.

Installation:

The installation of KQJ series cable tray can be per the local conditions can be laid according to the process requirements, such as plumbing, floor, hoisting under the beam, indoor and outdoor wall, tunnel, cable trench side wall mounted, but also on the open column.

When height of groove of cable tray is 50,100 mm, 6 connection holes for each end; when height of groove of cable tray is 150,200 mm, 12 connection holes for each end.

Support Spacing: it shall be less than or equal load curve, allowable load and support span.

Width: when we are electing the width of cable tray, we should leave enough spare space for new cables in the future.

Separated lying: when there are less power cables and control cables, they can be installed in the same cable tray, but there should be a separation plate between the power cable and control cable.

Fixing of cables: when the cable trays are horizontal laid, the connection point shall be in the position of 1 / 4, horizontal cable shall be fixed every 2 meters, the vertical cable trays shall be fixed every 1.5 meters.

Arrangement of cables in the cable tray

Weak current control cables shall be at the top layer, general control cables and low voltage power cable are downward arrangement. This kind of arrangement is good for shielding; good for cooling and site construction.

Spacing between cable trays

To ensure easy installation, cable tray and the spacing must satisfy the following data:

a ,when we are setting cable trays in the same support beam or in the same horizontal level, the net distance between adjacent cable trays should not be less than 50mm.

b, for two parallel cable tray, its net distance should not be less than 600mm.

When the cable trays are overlapped laid, the vertical distance shall meet the following data:

a, for power cable, it should be 300mm.

b, the control cable, it should be 250mm.

For the convenience of cable tray installation, the distance between cable tray and the top of the ceiling, beams and other obstacles at the bottom should meet the following data:

a, for power cable, it should be not less than 400mm.

b, for control cable, it should be not less than 250mm.

Notes

Vertical cable trays must be protected by cover on the area which is within two meters above the ground.

The position which is liable to mechanical damage must be protected by covers.

When the cable trays are horizontally laid, the selection of stride support shall be per the load curve; when the cable trays are vertically laid, there should be a fixing frame every 1 or 2 meters to make sure the stability of the cable trays.

When the cables in the cable tray are lead from horizontal direction to vertical direction, there must be a guide plate to protect the cable from damage.

When the material of cable tray is steel, there should be a reliable grounding wire; cable trays must be connected with the main grounding wire.



Отправить запрос, связаться с поставщиком

Кому: Hebei FUSHENG FRP CO.,LTD
Ваш E-mail:
Текст письма:


Send to other suppliers

Другие товары поставщика

Large GRP Tank Production Line
Large GRP Tank Production Line FW-10000VI Computer Control Site The major properties of the equipment are below. FW-15000VI Computer Control Site Winding Machine The major prope...
Process Equipment
Process Equipment For chemical recovery and pollution control, HBFS offers process equipment such as: This equipment handles the full range of dynamic and hyd...
GRP Chimney & Flue
GRP Chimney & Flue GRP (Glass Reinforced Plastic) or (Fiber Reinforce Plastic) Chimney and Flue HBFS can design, supply, assemble and install chimney or flue at plan...
Caustic Soda Flakes
Caustic Soda Flakes Note: We sold as an export agent for a manufacturer in our local place, Because we are in a small city and many companies have no person with abi...
 Pultruded Fiberglass Shapes
Pultruded Fiberglass Shapes Cable trayis assembled by pultruded/FRP profiles;suitable for electrical cable, control cables, lightening cable and fittings. There are , fibergla...
Все товары поставщика

Похожие товары

РЕАКТОР С МЕШАЛЬНЫМ ЛОПАСТНЫМ УСТРОЙСТВОМ
РЕАКТОР С МЕШАЛЬНЫМ ЛОПАСТНЫМ УСТРОЙСТВОМ Продавец: Jiangsu Sunkaier Industrial Technology Co., Ltd. РЕАКТОР С МЕШАЛЬНЫМ ЛОПАСТНЫМ УСТРОЙСТВОМ ОПИСАНИЕ Лопастной мешающий реактор типа SK3000E-...
Intelligent Mechanical Equipment
Intelligent Mechanical Equipment Продавец: CITIC IC LUOYANG HEAVY MACHINERY CO., LTD With the development of modern science and technology, industrial arm is a kind of high-tech auto...
Horizontal Centrifuge Machine
Horizontal Centrifuge Machine Продавец: CITIC IC LUOYANG HEAVY MACHINERY CO., LTD TWZ series horizontal vibratory centrifuge belongs to the centrifugal dewatering machine, the ser...
Wet Grid Ball Mill
Wet Grid Ball Mill Продавец: CITIC IC LUOYANG HEAVY MACHINERY CO., LTD Wet ball mill is a kind of energy-saving industrial grinding mill which adopts rolling bearings a...
Vertical Centrifuge
Vertical Centrifuge Продавец: CITIC IC LUOYANG HEAVY MACHINERY CO., LTD The vertical centrifuge machineis made up of the screen which diameter range from 700 to 1,000 mm...