CAS 104-66-5
Ethylene glycol diphenyl ether CAS 104-66-5
| Purity / Analysis Method |
>99.0%(GC) |
| Molecular Formula / Molecular Weight |
C14H14O2= 214.26 |
| Physical State (20 deg.C) |
Solid |
| Storage Temperature |
Room Temperature (Recommended in a cool and dark place, <15°C) |
| CAS RN |
104-66-5 |
Specifications
| Appearance |
White to Light yellow powder to crystal |
| Purity(GC) |
min. 99.0 % |
| Melting point |
95.0 to 98.0 °C |
| NMR |
confirm to structure |
Properties (reference)
| Melting Point |
97 °C |
| Boiling Point |
185 °C/12 mmHg |
104-66-5 – Risk and Safety
| Risk Codes |
51/53 – Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. |
| Safety Description |
S22 – Do not breathe dust.
S24/25 – Avoid contact with skin and eyes.
S61 – Avoid release to the environment. Refer to special instructions / safety data sheets.
S36 – Wear suitable protective clothing.
S29/56 – |
| UN IDs |
UN 3077 9 / PGIII |
| WGK Germany |
3 |
| TSCA |
Yes |
| HS Code |
29093090 |
104-66-5 – Reference Information
| LogP |
3.81 at 25℃ |
| use |
1.2-diphenoxyethane (DPE) has attracted much attention as a new type of heat-sensitive material sensitizer and a potential polyolefin catalyst additive. |
| Synthesis method |
Only a few documents have reported the synthesis of 1. 2-diphenoxy ethane, mainly through phenol and 1. 2-dichloroethane or ethylene glycol sulfonate in alkaline water or ethanol medium. The reaction is prepared as the starting material. The yield is reported to be as high as 80%, but the product contains more impurities, the synthesized crude product needs to be purified by high temperature distillation (collection temperature is about 200 ℃, vacuum degree is below 700Pa). This process consumes a lot of energy, and due to the high freezing point of the product, it is easy to block the pipeline, which puts forward high requirements on the equipment.
There are also reports of synthesizing 1.2-diphenoxy ethane with 1.2-dibromoethane and phenol as raw materials and ethanol as solvent, but the yield is only 30%. In the reaction, 1.2-dibromoethane is easy to undergo side reactions to convert into bromoethylene, resulting in low yield. |
Другие товары поставщика
|
|
Rheology modifier STD-9010 |
Composition: Polyurea mixture solution
Appearance: yellow transparent solution
Active ingredient: 50%
Solvent: N-methylpyrrolidoneScope of Appli... |
|
|
High boiling aromatic hydrocarbon solvent |
Introduction
High boiling point aromatic hydrocarbon solvent than the traditional toluene, xylene little toxicity, Flash point is high, use and tr... |
|
|
Mixed Etherified Melamine Resin |
Introduction
This category of products is mainly made by reacting butanol, methanol in a certain proportion with hydroxymethyl melamine. It has th... |
|
|
Leveling agent STD-236N |
Introduction
Composition: Polyether modified silicone oil
Appearance: light yellow viscous liquid
Active ingredient: 100%
Solvent: None
Applic... |
|
|
PVF oil pipe coating |
Product Introduction
Used for automobile oil pipes.
PVF coating characteristics:
(PVF) coating is the abbreviation of polyvinyl fluoride (Polyvi... |
Все товары поставщика
Похожие товары
