CAS 104-66-5
Ethylene glycol diphenyl ether CAS 104-66-5
| Purity / Analysis Method |
>99.0%(GC) |
| Molecular Formula / Molecular Weight |
C14H14O2= 214.26 |
| Physical State (20 deg.C) |
Solid |
| Storage Temperature |
Room Temperature (Recommended in a cool and dark place, <15°C) |
| CAS RN |
104-66-5 |
Specifications
| Appearance |
White to Light yellow powder to crystal |
| Purity(GC) |
min. 99.0 % |
| Melting point |
95.0 to 98.0 °C |
| NMR |
confirm to structure |
Properties (reference)
| Melting Point |
97 °C |
| Boiling Point |
185 °C/12 mmHg |
104-66-5 – Risk and Safety
| Risk Codes |
51/53 – Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. |
| Safety Description |
S22 – Do not breathe dust.
S24/25 – Avoid contact with skin and eyes.
S61 – Avoid release to the environment. Refer to special instructions / safety data sheets.
S36 – Wear suitable protective clothing.
S29/56 – |
| UN IDs |
UN 3077 9 / PGIII |
| WGK Germany |
3 |
| TSCA |
Yes |
| HS Code |
29093090 |
104-66-5 – Reference Information
| LogP |
3.81 at 25℃ |
| use |
1.2-diphenoxyethane (DPE) has attracted much attention as a new type of heat-sensitive material sensitizer and a potential polyolefin catalyst additive. |
| Synthesis method |
Only a few documents have reported the synthesis of 1. 2-diphenoxy ethane, mainly through phenol and 1. 2-dichloroethane or ethylene glycol sulfonate in alkaline water or ethanol medium. The reaction is prepared as the starting material. The yield is reported to be as high as 80%, but the product contains more impurities, the synthesized crude product needs to be purified by high temperature distillation (collection temperature is about 200 ℃, vacuum degree is below 700Pa). This process consumes a lot of energy, and due to the high freezing point of the product, it is easy to block the pipeline, which puts forward high requirements on the equipment.
There are also reports of synthesizing 1.2-diphenoxy ethane with 1.2-dibromoethane and phenol as raw materials and ethanol as solvent, but the yield is only 30%. In the reaction, 1.2-dibromoethane is easy to undergo side reactions to convert into bromoethylene, resulting in low yield. |
Other supplier products
|
|
PTFE powder coating |
Product introduction
Polytetrafluoroethylene (PTFE), commonly known as “the king of plastics”, is a polymer compound formed by the pol... |
|
|
PUR reactive polymer |
Introduction
PUR reactive polyurethane is a single component, moisture reactive structural adhesive.
It has the characteristics of fast initi... |
|
|
Promoter TBSI CAS 3741-80-8 |
3741-80-8 –Names and Identifiers
Name
N-Benzothiazol-2-ylsulfanyl-N-tert-butyl-benzothiazole-2-sulfenamide
Synonyms
VANAX 833VA... |
|
|
Three proof adhesive |
Three proof adhesive,also known as circuit board protective adhesive or coating adhesive, is applied to the surface of the circuit board to form a ... |
|
|
Sealing application adhesive |
Introduction
Polyurethane and epoxy resin materials, different models of products can provide targeted insulation strength, flame retardant perfor... |
All supplier products
Same products
