AKRON abrasion testing machine

Product Introduction

AKRON wear testing machine is used with the balance, specially testing the wear resistance of rubber products such as soles, tires, car tracks, etc. The counters are electronic automatic, which can set the wear revolution, and automatically stop when the set revolution is reached.

Standard

GB/T 1689 standard, ISO:4661-1:1993. ISO 2481:1988. ISO 471:1983. ISO 1826:1981

Test size

Outer diameter 2 ", inner diameter 1/2 ", thickness 1/2 ", circumference 220mm, hardness 60——70

Machine operation method

1. Prepare the core of the specimen according to the conditions of obtaining the specimen. And record its exact weight.

2. Fix the specimen core on the core shaft seat, and then adjust the Angle of the specimen. (Usually set to 15∘)

3. Different test methods are divided into high standards and low standards according to material requirements.

3.1 High standard requirements:

a. Angle (the Angle between the test piece and the grinding wheel)15∘

b. Load :6 pounds

c. Pre-grinding revolutions :300 revolutions

d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test

e. Install the specimen core and set the wheel rotation times :3000 revolutions

f. After the wear is completed, remove the specimen, brush with a clean brush to remove the powder, and then weigh the accurate weight with a precision balance, which is the weight of the sample after the test

g. Substitute the formula to calculate the grinding amount

3.2 Low standard requirements:

a. Angle (the Angle between the test piece and the grinding wheel)15∘

b. Load :2 pounds

c. Pre-grinding revolutions :200 revolutions

d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test

e. Load back the specimen core and set the wheel rotation times :2000 revolutions

f. After wearing, remove the specimen, brush with a clean brush to remove the powder, and then weigh the exact weight with a precision balance

This is the test weight after the test

g. Substitute the formula to calculate the grinding amount

4. After all specimens have been tested, remove the weight and store it, and remove the debris on the machine.

Wear value calculation method:

Wear (volume m1)== Weight before test - weight after test

Specific gravity algorithm:

a. If the test material is heavier than water

Specific gravity = Weight in air ÷(weight in air - weight of sample in water)

b. If the test material is lighter than water

Specific gravity = weight in air ÷ volume

Technical parameters

Grinding wheel diameter Φ150mm, 40mm(w)， particle size 36#

Grinding wheel speed 34±1r/min

The incline range of the test material is adjustable from 0 to 35°

Test shaft speed (GB)76±2r/min

Load 26.7N±0.2

Counter LED, 0——99.999.999

Volume (W×D×H) 60 × 50 × 45cm

Weight (approx) 60 kg

Power 1 #,AC220V, 50Hz (depending on country or designation)

Другие товары поставщика

	IULTCS Veslic Leather Abrasion Tester
	Water injection counterweight dummy	Product Introduction This counterweight dummy can be filled with water, the torso and the bottom are separated, independently filled with water o...
	Initial drying resistance test machine	Standards GB9779-2015 GB14907-2002 GB/T9271-2008 JG/T24-2000 Technical parameters 1. axial fan, can be stepless speed regulation 2.Test th...
	Air - tightness Testing Device for Automotive Connectors-QINSUN	The air - tightness testing device for automotive connectors uses the pressure principle to conduct non - destructive tightness tests on containe...
	High-Power Lamp tube （1500W~12000W)	Applicable Standards High-power lamp tubes adhere to global safety and performance benchmarks, including: IEC 60598-1(Luminaires – Genera...

Все товары поставщика

Похожие товары

	Common Rail Injector Valve F00R J02 012	Продавец: 868983	Common Rail Injector Valve F00R J02 012 David Chen
	Common Rail Injector Valve F00R J02 005	Продавец: 868983	Common Rail Injector Valve F00R J02 005 David Chen
	Common Rail Injector Valve F00R J01 941	Продавец: 868983	Common Rail Injector Valve F00R J01 945 David Chen
	Common Rail Injector Valve F00R J01 941	Продавец: 868983	Common Rail Injector Valve F00R J01 941 David Chen
	Common Rail Injector Valve F00R J01 924	Продавец: 868983	Common Rail Injector Valve F00R J01 924 David Chen