Fogging Tester，automotive interior fogging tester，6 station mist tester

Fogging Tester is mainly used to test the evaporation of volatile components in materials such as interior plastic parts of automobiles and aircraft, polyurethane, textiles, leather, adhesives, non-woven fabrics, and thermoplastic elastomers at high temperatures.

Application

1. Evaluating Material Fogging Performance

The fogging tester is primarily used to evaluate the evaporation of volatile components from interior materials of automobiles, aircraft, and other vehicles at high temperatures. These interior materials include plastic parts, polyurethane, textiles, leather, adhesives, non-woven fabrics, and thermoplastic elastomers. The test reveals the generation of volatile substances from the materials at high temperatures, thus determining their fogging performance.

2. VOC Detection

This instrument is one of the essential instruments for VOC (Volatile Organic Compounds) detection in the automotive interior industry. The test provides evaporation data of volatile substances from interior materials at high temperatures, providing important information for controlling indoor air pollution and ensuring the health of drivers and passengers.

3. Screening Environmentally Friendly Materials

Through testing with the fogging tester, environmentally friendly interior materials that meet environmental standards can be selected, helping automobile manufacturers improve the market competitiveness of their products while reducing environmental pollution.

Standard Test

DIN 75201: Automotive trim material fogging resistance.

ISO 6452: Coated fabrics fogging behavior in vehicle interiors.

SAE J1756: Automotive interior material fogging test protocol.

BS EN 14288 & QB/T 2728: Leather and textile fogging evaluation.

PV 3920/3015: VDA-standard fog value determination for non-metallic materials.

ES-X83231. NES M0161. GM 9305P: OEM-specific fogging requirements for automotive suppliers.

Feature

Dual-Bath System:

High-Temperature Bath: 670×490×540mm, 3kW heating power (up to 150°C).

Low-Temperature Bath: 400×220×520mm, 500W cooling capacity (0–100°C).

Automated Controls:

Digital thermoregulator with microprocessor for precise temperature programming.

Programmable timer (1–9999 min) with auto-stop and end-test buzzer.

Modular Accessories:

18/8 stainless steel test cups, flat beakers, and chrome steel rings for sample mounting.

Six interchangeable cooling plates and haze/gloss measurement kits.

Safety Compliance:

CE-certified with anti-acid epoxy coating, emergency stop, and overpressure relief.

Parameters

Parameter	Specification
High-Temperature Range	Room temperature – 150°C (280°C optional)
Low-Temperature Range	0–100°C
Temperature Stability	±0.1°C (at 200°C)
Heat-Up Time	<45 min (to 150°C)
Cooling Capacity	500W (low bath)
Power Supply	AC 220V, 50Hz, 3.5kW
Dimensions	500 (W) × 650 (D) × 600 (H) mm
Net Weight	50 kg (excluding thermal media)
Data Interface	USB 2.0. remote sensor compatibility
Safety Systems	Magnetic switch, thermostat, audible alerts

Accessoriess

Standard accessories：Main unit *1. constant temperature controller (cooling device) *1. glass beakers (fogging cups) *6.circular glass plates *6. square glass plates *6 (for reflection method testing), haze meter *1. metal rings *6.Fluororubber sealing rings *6. aluminum foil *1 pack, φ80mm sampler *1. dioctyl phthalate (DOP), silicone oil (heat transfer oil) / 32Kg, diisodecyl phthalate (DIDP)

Test Procedures

1.First of all , get the accessories and test samp.

2.Prepare an aluminum foil,place it in the scale to weigh it, and record the value.

3.Place aluminum foil and glass plate over the fog cup.

4.Set the cycle parameters of the low temperature control box, set host temperature and time parameters.

5.Start the instrument,the sample is heated inithe fog cup.

is started.When the timing is reached, remove.

the aluminum paper fZrom the station.

6.Put it into the scale again and weigh it, and record the value.

Другие товары поставщика

	Stain resistance tester for architectural coatings	Product Introduction The interior wall coating in architectural coatings is often polluted by some pollution from daily necessities, people often ...
	Shoe heat insulation testing machine -- sand bath	Standard GB/T 20991: Determines thermal insulation of safety shoe soles under simulated hot surface exposure. EN ISO 20344: European standard for...
	Wire Torsion and Winding Tester	The Wire Torsion and Winding Tester is a versatile instrument designed to perform both torsion and winding tests on metal wires. It evaluates the m...
	Wear Track Profilometer	Applicable standards When the probe type material surface abrasion measuring instrument is tested, it usually needs to follow certain standards an...
	Standard Helmet Visual Field Tester	Standards EN 1078:2023: Helmets for Pedal Cyclists, Skateboarders, and Roller Skaters CE Certification(Conformité Européenne) Equi...

Все товары поставщика

Похожие товары

	Air Intake Filter Test System	Продавец: Standard Groups	The Air Intake Filter Test System is designed for testing industrial air filters and engine air f...
	Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging	Продавец: Standard International Group (HK) Limited	The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f...
	Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester	Продавец: Standard International Group (HK) Limited	The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter...
	HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ...
	VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine	Продавец: Standard International Group (HK) Limited	The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia...