Surface adhesion testing equipment factory price

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Standards

JIS L 1066 (Testing Methods for Woven Fabrics)

JIS L 1085 (Testing Methods for Nonwoven Fabrics)

JIS L 1086 (Testing Methods for Textile Products)

JIS P 8139 (Determination of Adhesion and Peel Strength of Paper and Board)

Parameters

Parameter	Specification
Measurement range	Load cells available: 0–100 gf, 0–2000 gf
Traveling speed	Clamp traveling speed: 50–500 mm/min
Measurement speed	Opposing clamp speed: 100–1000 mm/min
Travel distance	Stroke per clamp: 150 mm
Specimen size	Maximum: 200 mm × 75 mm
Output signal	0 to ±5 V (within ±0.05% FS)
Frequency response	2 kHz / −3 dB
Operating environment	Temperature: 0–50 °C
	Relative humidity: ≤85%, non-condensing
Power supply	AC 100 V, 50/60 Hz
Dimensions	W 630 mm × D 310 mm × H 350 mm

Features

Wide measurement capability from very low to relatively high adhesion forces

Supports multiple test modes, including T-peel, 180° peel, tensile, tear, and surface adhesion tests

Desktop-type design suitable for laboratory and on-site testing

Portable structure allows convenient measurements in different locations

Simple zero balance and calibration procedures enable quick and intuitive operation

Stable opposing-motion mechanism ensures consistent and repeatable test results

Accessories

(1) Load sensor

(2) Relay cable, 1 m

(3) Power cable with E-type plug, 2 m

(4) Acrylic protective cover

(5) Tool set

(6) Parts storage box

(7) Operating manual

Optional: Tribosoft analysis software

Test Procedures

Prepare the specimen according to the required test method and standard.

Secure each end of the specimen firmly in the opposing clamps.

Select the appropriate load sensor and verify zero balance.

Set the test speed and travel distance based on the test requirement.

Start the test, allowing the clamps to move at equal speed in opposite directions.

Record the resistance measured by the load sensor during the test.

Analyze the data to determine peel strength, tensile strength, or adhesion force.

Другие товары поставщика

	Qinsun Ci xenon lamp aging test chamber	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Ci Series Weather-Ometers are the most widely used rotating rack water-cooled xenon-arc...
	Mask Air Tightness Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com TheAir TightnessTesterismainly used for air tightness testing of masks and respirators unde...
	Vertical flame test chamber	Whats/App: +86 156 1874 6768 Web: standard-groups.com Introduction The Vertical Flammability Chamber, designed for American Standards, measures ...
	Thermal - Cold Cycle meter	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard BS 7291: Compliant for thermal cycling tests on thermoplastic pipe systems (176...
	Thrust Washer Friction Testing Machine	The thrust washer friction testing machine is mainly used to simulate the frictional contact of materials under specific working conditions and t...

Все товары поставщика

Похожие товары

	Surface adhesion testing equipment factory price	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards JIS L 1066 (Testing Methods fo...
	Continuous load scratch resistance tester manufacturer	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO DIS 12137-2 (Plastics &mda...
	High precision continuous load surface tester	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB/T 6040-2008 Test Method for...
	Multi-function surface performance test system	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB/T 6040-2008 Test Method for...
	Laboratory tribology research equipment	Продавец: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB/T 6040-2008 Test Method for...