CE Certified Block-on-Ring Test Machine for Quality Control
Get a quote：
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The Block-on-Ring Test Machine is a tribological testing system designed to evaluate friction and wear performance under stable line-contact conditions. Using aBlock-on-Ringcontact configuration, the system maintains constant linear contact and steady rotational speed, allowing you to reliably simulate real industrial contact conditions.The machine supports dry and lubricated friction testing for lubricants, coatings, polymers, ceramics, and composite materials. A pneumatic loading system and programmable control enable stepwise or ramped control of load, speed, temperature, and motion mode, ensuring repeatable and standardized wear testing.
Standards
The system is suitable for testing in accordance with the following international standards and methods:
(1) ASTM D2509 — Standard Test Method for Measurement of Load-Carrying Capacity of Lubricating Grease
(2) ASTM D2714 — Standard Guide for Calibration and Operation of Ring-on-Block Wear Test Machines
(3) ASTM D2782 — Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids
(4) ASTM D2981 — Standard Test Method for Evaluation of Solid Lubricant Films under Oscillating Motion
(5) ASTM D3704 — Standard Test Method for Wear Characteristics of Lubricating Grease under Oscillating Motion
(6) ASTM G77 — Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Ring-on-Block Geometry
(7) ASTM G137 — Standard Test Method for Ranking Resistance of Polymeric Materials to Sliding Wear Using Ring-on-Block Geometry
(8) Proposed STM — Wear Testing of Dry Film Solid Lubricants under Unidirectional Motion
Parameters
| Item | Technical Parameters |
|---|---|
| Speed range | Standard: 60–3.600 RPM; Optional: 0.5–7.200 RPM |
| Linear speed | Automatically calculated from shaft speed; programmable RPM setpoints, ramp rates, cycles, and test sequences |
| Load range | Dual-zone pneumatic loading: Low load 10–100 lbs; High load 50–1.300 lbs |
| Temperature range | Standard chamber: Ambient to 200 °C; Optional pressure chamber: Ambient to 250 °C; External chiller for sub-ambient testing |
| Friction force measurement | Electronic load cell, standard range 0–250 lbs; optional low-load range 0–25 lbs |
| Motion modes | Unidirectional rotation or oscillating motion (5°–720°) |
| Test control mode | Time-based, cycle-based, or limit-based automatic shutdown |
| Power supply | 220 VAC, single phase, 50/60 Hz |
| Compressed air | 80 psig, clean and dry |
| Benchtop dimensions | 1.829 × 610 × 762 mm |
| Machine weight | 163 kg |
| Shipping dimensions | 1.220 × 1.016 × 1.067 mm |
| Shipping weight | 246 kg |
Features
(1) Stable line-contact configuration that avoids rapid contact pressure reduction common in point-contact testers
(2) Wide temperature control range supporting high-temperature and optional low-temperature wear testing
(3) Dual-zone pneumatic loading system covering low-load and high-load test requirements
(4) Programmable control of speed, load, temperature, oscillation angle, cycles, and test sequence
(5) High-precision electronic friction force measurement suitable for low-load testing
(6) Support for dry friction and lubricated testing with direct lubricant injection
(7) Multiple motion modes including unidirectional and oscillating motion
(8) Reliable simulation of industrial contact and wear conditions
Accessories
(1) StandardBlock-on-Ringadapter
(2) Inclined cylinder contact adapter
(3) Flat specimen contact adapter
(4) Point contact testing adapter
(5) Temperature-controlled test chamber
(6) Optional pressure test chamber
(7) External chiller for low-temperature testing
(8) Electronic load cell for friction force measurement
(9) PC-based control and data acquisition system
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Laboratory Flame Spread Tester for Insulation Panels | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards This tester conforms to the following national and international standards: GB/... |
 |
Light transmittance fog meter | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applicable standards: GBT 2410-2008: Determination of light transmittance and fog degree o... |
 |
Walk-in High Temperature Aging Test Room ,Walk in High Temperature Environmental Test Chamber | Whats/App: +86 156 1874 6768 Web: standard-groups.com TheHigh-Temperature Aging Chamberis designed to simulate high-temperature and harsh environ... |
 |
Footwear Dynamic Waterproof Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Footwear Dynamic Waterproof Tester is designed to evaluate the waterproof performance o... |
 |
ASTM F1566 Mattress Durability Fatigue Testing Machine | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Mattress Durability Fatigue Testing Machine evaluates the fatigue resista... |
Похожие товары
 |
Высокоскоростная экструзионная линия для производства гофрированных труб с двойными стенками из ПЭВП с водяным охлаждением | Продавец: Shandong HUASU Plastic Technology Co.,Ltd. | Формы имеют структуру с двойным каналом потока и фильерную головку, обработанную азотированием и ... |
 |
PanEVAP & MVR system | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
