Hydraulic Liner Hanger Tie-Back Assembly

The tie-back assembly is a special cementing tool for tieback operation.

Tieback equipment allows existing liners with a receptacle to be extended to the surface or farther up hole, and provides a high-pressure seal at the top of a cemented or uncemented liner. TIW offers variety of tieback seal nipples and tieback packers to accommodate liner top extension and remedial operations.

Tieback Procedures of Hydraulic Liner Hanger Tie-Back Assembly

Measure and drift the casings carefully and clean all the threads.

Calculate the kelly-up of the casing (the particular part of the last casing which is above the rotary table) and arrange the casing string.

Prepare several casings, which are approximately 0.5m shorter than the others and convenient for kelly-up calibration. (The actual kelly-up is not equal to the calculated value due to measurement error and the remaining threads of the casings.)

Connect the milling shoe and trip in. Polish the inner surface of the polished bore receptacle, make sure there is no debris.

Note the depth of the milling shoe when it reaches the top of the seal assembly (judge from the changes on pressure and WOB). Then lift the drill string for 1m.

Use a drilling rate of 40～50rpm and a normal flow rate. Slowly lower the drill string. Polish the inner surface of the polished bore receptacle twice or three times. Each time polish 3～4min. During the last polishing, apply an additional load of 2～3t when the torque suddenly increases (the milling shoe reaches the top of the seal assembly) during the last polishing. Polish for another 2~3min and note the depth of the milling shoe, which is an important clue for the casing setting depth.

Circulate with high flow rate for 5min.

Trip out and check the milling shoe. If there is a circle of polished trace and the diameter is equal to the I.D. of the left thread on the seal assembly, then the milling shoe have reached the bottom of the polished bore receptacle.

Features ofHydraulic Liner Hanger Tie-Back Assembly

With the guide shoe and circulate bore, it can stab into polished bore receptacle before cementing, more convenient than conventional cementing which pumps down cement before stabbing.

With its streamline shape, the guide shoe can stab into polished bore receptacle easily.

The Tieback Seal Assembly with three stacks of molyglass seal is designed for high-pressure and high-temperature liner tieback completions. Available in seal length is 1.2m.

Technical Parameters ofHydraulic Liner Hanger Tie-Back Assembly

Specifications, mm	Φ177.8	Φ127.0
Sealing capacity, MPa	25	25
Heat-proof Rating, ℃	120	120
Available Sealing Length, mm	1200	1200
	Φ155	Φ108

SAIGAO GROUPis one of professional oil equipment suppliers. We provide Fishing Tools, Mud Pump Parts, tie back receptacle, tie back cementing, tie back casing, liner hanger assembly, hydraulic hanger, casing tie back, tie back linerand so on. Want to know about tie back liner procedure? Please contact us.

Другие товары поставщика

	Overview of Manifold	A manifold is a combination of multiple pipes. The manifold includes gate valves, pipelines, pipe fittings, pressure gauges, and electronic sensing...
	Cement Manifold	Cementing manifold is used to control the cement fluid from cementing pump and transform the cement fluid to wellhead and accomplish cementing oper...
	Cementing Plug	Saigao Rubber plug used to separate the cement slurry from other fluids, reducing contamination and maintaining predictable slurry performance. Two...
	BW450 / 5 Horizontal Three Cylinder Reciprocating Single Acting Piston Pump	BW450 / 5 Mud Pump is widely used in mining, drilling, coal, railway, highway, water conservancy and hydropower, bridges, high-rise buildings, foun...
	Key Seat Wiper	Key Seat wiper Sliding sleeve type key seat reamer consists upper sub, mandrel, lower sub, sliding sleeve and so on, as shown in diagram. The slidi...

Все товары поставщика

Похожие товары

	OEM подгонянный горизонтальный шестеренчатый насос масла смазывания холодильника серии LB	Продавец: Shenghui Pump	Шестеренчатый насос серии LB для морозильной камеры предназначен для перекачки всех видов механич...
	OEM подгонянный горизонтальный шестеренчатый насос масла смазывания холодильника серии LB	Продавец: Shenghui Pump	Шестеренчатый насос серии LB для морозильной камеры предназначен для перекачки всех видов механич...
	Новое поступление Горизонтальный дуговой шестеренчатый насос для перекачки масла серии YHCB	Продавец: Shenghui Pump	Дуговые шестеренчатые насосы серии YHCB предназначены для перекачки жидкостей высокой вязкости, т...
	Портативный насос передачи шестерни дизельного масла серии WCB нержавеющей стали высокой вязкости	Продавец: Shenghui Pump	Шестеренчатый масляный насос WCB легкий, небольшой по объему, удобный для переноски и перемещения...
	Шестеренные насосы высокого давления из нержавеющей стали серии ZYB для транспортировки отработанного тяжелого масла	Продавец: Shenghui Pump	Насос для отработанного масла серии ZYB используется для перекачивания тяжелого масла, дизельного...