Safety Helmet Roll-off Testing Equipment

• 

The safety helmet retention test equipment is a device used to evaluate the stability of a helmet's fit when subjected to impact. By simulating the pulling forces and impact scenarios of an accident, it accurately assesses the reliability of the helmet's retention system, providing a rigorous technical safeguard for the safety of cyclists. The equipment mainly consists of a simulated head form, a tensile loading system, an impact track, and a data acquisition system. During the test, the helmet is secured to the simulated head form according to standard wearing procedures, and the length of the helmet straps and the tightness of the buckles are adjusted to ensure a fit that matches actual wearing conditions.

Application

Apply an initial load of a certain force to the rear of the helmet. Then, let a weight specified by the standard fall from a certain height so that the impact force is also applied to the helmet. In this way, the wearing stability performance of the helmet can be evaluated.

Standard

IS 4151:Indian Standard for Protective Helmets

ECE R22.05:Uniform Provisions Concerning the Approval of Protective Helmets and Their Visors for Drivers and Passengers of Motor Cycles and Mopeds

Feature

Dynamic Tensile Testing: A tensile force is applied to the helmet using a tensile loading system, and the maximum tensile force is recorded to ensure the helmet does not detach during the test.

Impact Testing: The helmet is worn and slid down a track to impact a rigid obstacle at a specific speed, and whether the helmet detaches is recorded.

Data Acquisition: An accelerometer records the impact force on the headform, comprehensively evaluating the stability of the fastening system under dynamic impact.

Safety Protection: The equipment is equipped with a safety enclosure to prevent injury from flying helmet fragments during testing.

Parameters

Accessoriess

Anthropomorphic headform

Strap clamp

Force sensor

Impact drive assembly

Data acquisition and analysis system

Protection and limiting devices, etc.

Test Procedures

1. previously to the ambient temperature and sanitary conditions for the conditions of the helmet, should be placed on the appropriate head shape and fixed in the appropriate head.

2. In the median vertical plane of the helmet, a device that guides and releases the fall with a total mass of 3 kg ± 0.1 kg is attached to the rear of the shell.

3. 10 kg ± 0.01 kg of falling mass is released and lowered from a height of 0.5 m ± 0.01 m. The guiding device should ensure that the impact velocity is not less than 95% of the theoretical velocity.

Другие товары поставщика

	Coating abrasion resistance test device	Product Introduction: The determination of scratch resistance of the coating is very similar to the scratch test of the coating, but this test met...
	G234 Bed Blanket Flammability Tester	The test instrument is used to detect the flame resistance of the blanket fabric and the flame spread performance of the fabric surface. The test m...
	Vibration Table	Standard ASTM D999: Vibration testing of shipping containers and packaged products. TAPPI T819: Corrugated box performance under simulated tran...
	Carbon Black Content Tester	Standard GB 13021-1991: Determination of carbon black content in polyethylene compounds. GB/T 2951.41-2008: Test method for carbon black and ash ...
	Artificial turf wear tester	Standard FIFA Quality Programme: Exceeds 2015/2016 handbook requirements for artificial turf abrasion resistance testing. EN 15330-1: European st...

Похожие товары

	Air Permeability Tester STD- F8	Продавец: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Продавец: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Продавец: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Продавец: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Продавец: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...