Low-Temperature Bending Resistance Tester

• 

Applicable Standards

The tester adheres to international standards for material testing at low temperatures, including:

ISO 4674-2(Rubber- or plastics-coated fabrics – Determination of low-temperature bend test)

ASTM D1790(Standard test method for resistance of organic coatings to the effects of rapid deformation (impact))

GB/T 2423(China’s national standard for environmental testing – Cold tests)

EN 60068-2-1(Environmental testing – Cold tests for electronic components)

SAE J2339(Cold temperature impact resistance for automotive coatings)

These standards ensure consistent evaluation of material behavior under thermal and mechanical stress.

Working Principle

The tester operates bycombined thermal and mechanical stress:

Temperature Conditioning: Samples are cooled to -70°C in a climate chamber.

Bending Cycle: A motorized arm repeatedly bends the sample at a preset angle (e.g., 90° or 180°) and frequency (e.g., 100 cycles/min).

Cycle Execution: The test runs until surface cracks appear, or a predefined cycle count (e.g., 20.000 cycles) is reached.

Damage Assessment: Post-test, samples are evaluated for cracking, delamination, or coating failure using microscopy or visual grading.

Test Principle & Applications

Cold Flexibility Testing (ISO 4674-2/ASTM D1790):

Samples are bent 10.000–50.000 times at -40°C to simulate polar or alpine conditions.

Results are graded based on crack appearance:

Pass: No visible cracks or coating separation.

Fail: Cracks exceeding 0.5 mm in width.

Key Industries:

Aerospace: Validating aircraft fuel lines and sealants.

Automotive: Testing battery packs and exterior trim for electric vehicles.

Construction: Assessing pipe insulation and roofing membranes.

The Low-Temperature Bending Resistance Tester is indispensable for manufacturers developing products for extreme climates, ensuring reliability and compliance with regulatory standards. Its precision and adaptability make it a cornerstone of materials testing in harsh environments.

Main Parameters

Другие товары поставщика

	AATCC KMS-M6 Washer, KMS-M6D Dryer	The AATCC KMS-M6 Washer and KMS-M6D Dryer are precision textile testing instruments designed to simulate industrial laundering and drying processes...
	Battery combustion tester	Battery combustion tester is a device that can be applied to the safety test of lithium-ion batteries, which can realize the simulation of the batt...
	Solar Cell Spread of Flame & Burning Brand Test Machine	This apparatus is based on UL 1730. IEC 61730-2 design and development. Is to simulate real conditions to assess roof and components of fire-resist...
	Water Vapour Permeability Tester	The Water Vapour Permeability Tester is a constant temperature and humidity instrument designed to evaluate the moisture permeability of waterproof...
	Taber Abrasion Resistance Tester	Taber Abrasion Tester is also referred to as Taber abraser or Taber abrader, which is used to evaluate the wear resistance of materials or finished...

Похожие товары

	Thrust Bearing Rolling Friction and Wear Testing Machine	Продавец: Standard International Group (HK) Limited	Applicable Standards: ASTM D3702 ASTM G99 ASTM G77 ISO 18535 Product Advantages: Simulates ...
	Falling Sand Abrasion Test machine	Продавец: Standard International Group (HK) Limited	The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance...
	Conveyor Belt Drum Friction Testing Machine	Продавец: Standard International Group (HK) Limited	Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes...
	Dry Sand Rubber Wheel Wear Tester	Продавец: Standard International Group (HK) Limited	The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater...
	Sliding Bearing Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua...