High and low temperature universal creep testing machine

Product Introduction:

High and low temperature universal creep testing machine is mainly used for non-metallic materials creep, stress relaxation, tensile, compression, bending, shearing, stripping, tearing and other tests.

Applicable standards:

GB/T 11546.1-2008 Determination of the creep properties of plastics - Part 1: tensile creep

GB/T 15048-94 Test method for compressive creep of rigid foam plastics

GB/T 20672-2006 Determination of compressive creep of rigid foam under specified load and temperature conditions

GB/T 104.1-2006 - Determination of tensile properties of plastics - Part 1

GB/T 1041-92 Test method for compression properties of plastics

GB/T 9341-00 Test method for bending properties of plastics

Main indicators:

1. Test force:

Maximum test force (kN) : 10

Effective force measurement range: 0.4%-100%FS(internal and external ungraded)

Resolution: 1/300000

Relative error: ±0.5%

2. Test speed:

Speed adjustment range: 0.05 —— 500mm/min(stepless speed regulation)

Speed relative error: ±0.5%

Control range of uniform test force rate and uniform deformation rate: 0.01% —— 5%FS/S

Uniform test force rate, uniform deformation rate control error: ±0.5%

Constant test force, constant deformation control range: 0.5% —— 100%FS

Constant test force, constant deformation control error: less than 10%FS is ±1% of the set value, greater than 10%FS is ±0.1% of the set value

3. Displacement (moving the beam)

Measuring range: 0 —— 999mm

Resolution: 0.001mm

Relative error: ±0.5%

Step 4 Transform

Beam deformation measurement accuracy: ±0.5%

Deformation measurement range in beam test: 860mm

Large deformation measurement accuracy: ±0.5%

Large shape measurement range: 25-1000mm

5. Host and accessories

Maximum test force kN 10KN

Effective test width mm: 420

Maximum travel of moving beam mm: 1160

Overall dimensions (length × width × height)mm: 900×480×1810

Maximum clamping force of wedge chuck (kN) : 10

Clamping range: plate mm: 0-8. rod mmφ : 6-φ16. compression device mm: φ70. bending device: support roll radius MMR2.5-R5.0

Roller diameter mm: φ5

Offset range mm: 120

Другие товары поставщика

	Geosynthetic direct shear drawing friction tester 丨Geotextile Test Machine	The friction characteristics of the interface of sand/geotextile were determined by testing the contact surface of standard sand/geotextile. This i...
	Shoelace Abrasion Tester SATRA TM154	Standards SATRA TM93、DIN-4843、QB/T2226、SATRA TM154 Principle Let shoelace cross the eyelet clamped on the fiber board, make the shoelace and eye...
	Shoelace anti-siphon tester 丨Shoelace Tester	Product Introduction Shoelace anti-siphon tester is suitable for all kinds of waterproof leather, leather, mesh, waterproof shoelace, ribbon water...
	Fabric Fiber Shedding Degree Tester (Friction Method) / Fabric Shedding Test Machine	Instrument Testing Principle Lay the specimen flat and fix it on the holder. Make the wet abrasive attached to the friction head perform reciproca...
	Geosynthetic Transmissivity Tester丨Geotextile Test Machine	Scope of application: It is used to measure the characteristics of the plastic drainage plate in the plane direction of the water flow under the s...

Все товары поставщика

Похожие товары

	Bottle Wall and Bottom Thickness Tester	Продавец: Standard Group (Hong Kong) Limited	The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
	Pinhole Tester / Pinhole Testing Equipment	Продавец: Standard Group (Hong Kong) Limited	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
	Cork Puncture and Chip Detection Instrument	Продавец: Standard Group (Hong Kong) Limited	The rubber stopper puncture debris detector is a device specifically used to detect the number of...
	Aluminum Ointment Tube Toughness Tester	Продавец: Standard Group (Hong Kong) Limited	The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
	Vacuum leak tester / Vacuum leak instrument	Продавец: Standard Group (Hong Kong) Limited	Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...