Fabric Fiber Shedding Degree Tester (Friction)
Instrument Testing Principle
Lay the specimen flat and fix it on the holder. Make the wet abrasive attached to the friction head perform reciprocating friction movements on the specimen under the specified load for a specified number of times with a certain stroke. Then compare it with the standard sample and visually rate the degree of fibers adhered to the abrasive to characterize the degree of fiber shedding of the specimen. It is suitable for factories, scientific research institutes, colleges and universities, import and export commodity inspection, textile testing in various provinces and cities.
Features
Touch screen controller: The number of frictions can be set arbitrarily.
Backup mechanical buttons for buttons in the touch screen: They can be used simultaneously, which is convenient and fast.
Pneumatic holder for specimen installation: Convenient and fast.
Equipped with a calender for adjusting the moisture content of the abrasive: The roll-off rate can be adjusted.
Complies with the standard: Appendix A of GB/T 40270 - 2021
Parameters
Stroke of the friction head: (200 ± 2) mm
Reciprocating speed: 30 times/min
Diameter of the circular friction head: (90 ± 1) mm
Outer diameter of the fixed clamp ring of the friction head: (120 ± 0.5) mm, inner diameter: (90 ± 0.5) mm
Diameter of the test washer: (113 ± 0.5) mm
Foam plastic washer: Diameter 105 mm, thickness 8 mm, unit area mass approximately 270 g/m²
Total mass of the friction load: (595 ± 7) g
Sandpaper: 600 - grit aluminum oxide water - washable sandpaper
Power supply: AC 220V, 50Hz
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Safety Harness Test Rubber Dummy | Application Performance testing of fall protection safety harness systems Performance evaluation of harness systems for guardrail work Verificat... |
 |
Melting Materials Dripping Test Machine,NF P92-505、EU 95/28/EC、ECE R118 Annex 7 FTech-NFP92-505 | Description： This tester meet international standards NF P92-505. EU 95/28 / EC, ECE technical specifications and requirements of R118 Annex 7 of ... |
 |
Electrochemical Corrosion and Wear Testing Machine | Electrochemical corrosion and wear testing machines are widely used in materials science, mechanical engineering, electronic engineering, aerospace... |
 |
Total Knee Joint Prostheses Wear Tester | Standard ISO 14243-1:2014: Specifies wear testing parameters for total knee prostheses, including axial loading, flexion/extension kinematics, and... |
 |
Carbon Black Content Tester | Standard GB 13021-1991: Determination of carbon black content in polyethylene compounds. GB/T 2951.41-2008: Test method for carbon black and ash ... |
Похожие товары
 |
Plastic Smoke Density Tester F313 | Продавец: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | Продавец: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Продавец: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Продавец: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Продавец: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
