Enamel Boiling Water Resistance Tester

• 

Product Introduction:

The enamel layer boiling water weight loss tester is designed according to QB/T 2590-2003 Appendix A, GBT99892-2015 /ISO 28706-2:2008 Determination of chemical attack resistance of enamel Part 2: Resistance to boiling acid, boiling neutral liquid and its vapor chemistry test requirements, and meets the boiling water weight loss test of acidic and alkaline media.

Installation steps:

1. A piece of stainless steel triangle plate is fixed up and down with hexagonal nuts, which is generally fixed when not in use.

2. Put on the rubber washer, and then put on the measured template.

3. Put the washer on, and then put the glass cylinder on.

4. Before the glass cylinder is placed, the heating ring is fixed on the glass cylinder, and the heating ring is fixed at 3-5mm from the bottom of the glass cylinder to avoid touching the rubber ring. At the beginning, observe whether the heating ring is loose (thermal expansion and contraction of the heating ring)， if there is, you can adjust some until it does not slide.

5. Then put the rubber ring and white PTFE square plate, if you want to do gas phase erosion, then directly put the template, you do not need to put white PTFE square plate.

6. Then put the stainless steel triangle plate and fix it with the wing nut, and tighten it by turns with even force.

7. Add distilled water to the glass interface to observe whether leakage, leakage, then continue to tighten; If there is no leakage, the test solution can be added according to the standard.

8. Plug in the retarder and connect the graduated condensate collector.

9. Then connect the serpentine condensing pipe, the cooling water enters from the lower end, and the upper end comes out. The condensing pipe is filled with water in the working state, and the water inlet is opened to let the water circulate slowly.

10. After the time is set, press the start button, adjust the voltage regulator to about 175V, and gradually reduce it until the water boils, until it is balanced, and observe that the water droplets of the condensate recycler are between 30 and 50 drops per minute.

11. Please conduct standard test and operate the equipment according to standard technical requirements, pay attention to electrical safety and anti-scald measures, and do not touch the device in the test area during heating.

12. Pay attention to the protection of glass accessories, because it is fragile, please handle gently in the disassembly process!!!

13. After the test is completed, cut off the power supply, turn off the cooling water, pour out the test solution according to the specification, and finally take out the template and weigh it.

Другие товары поставщика

	High Velocity Impact Tester	Main Purpose To test the impact - resistance performance of glasses, goggles and face shields at a certain speed. Applicable Standards SNELL S...
	Friction Charging Tester	Standards compliant:JIS L-1094;JIS T-8118;ZB W 04008-89;GB / T12703.2-2009;GB 12014-2009;GB / T23316-2009Calculation formula:Q = CV / AHere, C: the...
	Vertical Tray Fire Test Apparatus/UL1685/IEEE 1202	This tester is based on IEEE1202 and IEEE 383 standard design and development. This tester is used to assess single or bunched cables under defined...
	Shoelace wear tester	Main uses: Shoelace wear tester is mainly used to evaluate the durability and wear resistance of shoelaces. In the test, the LACES are usually fix...
	Dry microbial penetration resistance meter	DryMicrobial Penetration Resistance Testeris designed to determine determine the penetration resistance of material to bacterial on dry particulate...

Похожие товары

	Custom Stainless Components for OEM Applications	Продавец: Yongjia County Yaokang Technology Co., Ltd.	Our stainless steel float balls are designed for float valves, water tanks, and industrial liquid...
	FH-77 Dissolved hydrogen meter	Продавец: Коллирон электроникс лимитед	Pen type dissolved hydrogen detector / dissolved hydrogen meter: used to measure the dissolved hy...
	Xenon Arc Weather Ometer	Продавец: Standard Group (Hong Kong) Limited	Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ...
	Xenotest | Light Fastness Tester Si220 (SunTest)	Продавец: Standard Group (Hong Kong) Limited	Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ...
	Ozone Aging Chamber	Продавец: Standard Group (Hong Kong) Limited	Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum...