Total Hip Joint Prostheses Wear Tester

Standard

YY/T 0651.1-2016 (China): Specifies wear testing parameters for total hip prostheses, including angular motion, loading modes, and environmental conditions.

ISO 14242-1:2014 (International): Defines protocols for simulating physiological loading and kinematics during hip joint wear testing.

ASTM F3047M-15: Additional compliance for advanced testing scenarios including edge loading and micro-separation.

Product Advantages

Triaxial Motion Simulation: Replicates full physiological motion profiles (flexion/extension ±100°, abduction/adduction ±30°, internal/external rotation ±40°).

Dynamic Load Control: Dual-peak loading up to 4.500 N with 0.1% force accuracy.

Biorelevant Environment: Temperature-controlled (37±2°C) lubrication bath with 30±2 g/L protein concentration.

Extended Durability: Capable of 5+ million cycle testing with <0.5% drift in calibration.

Automated Compliance: Pre-programmed ISO/YYT test protocols with real-time data validation.

Modular Design: Six-station configuration allows parallel testing of multiple specimens.

Product Features

Electrohydraulic Actuation: Six independent servo-hydraulic actuators for precise motion control.

3D Force/Torque Sensors: Multi-axis sensors measure axial forces and torsional moments simultaneously.

Temperature-Controlled Bath: Recirculating lubrication system with protein concentration monitoring.

High-Resolution Imaging: Optional integration with micro-CT systems for in-situ wear analysis.

AI-Powered Analytics: Machine learning algorithms predict wear rates from initial test cycles.

Safety System: Emergency stop, over-pressure relief, and laser-based specimen breakage detection.

Technical Parameters

Parameter	Specification
Angular Motion Range	Flexion/Extension: ±100° Abduction/Adduction: ±30° Rotation: ±40°
Max. Axial Force	±4.500 N (1.000 N resolution)
Load Control Accuracy	±0.5% of reading (0–4.500 N)
Frequency Range	0.1–5 Hz (programmable waveforms)
Temperature Control	37±2°C (PT1000 sensors)
Lubrication System	15L capacity with protein skimmer and bubble trap
Data Acquisition	100 kHz sampling rate (16-bit resolution)
Power Requirements	220V/110V ±10%, 50/60Hz, 2.500W
Dimensions (W×D×H)	1.800 × 1.200 × 2.000 mm
Weight	950 kg (including bath and control cabinet)
Noise Level	<65 dB (A-weighted)

Standard Accessories

Hip Simulator Fixture Kit:

Self-centering femoral head adapters (16–32 mm)

Acetabular cup positioning jigs (60° inclination standard)

Biorelevant Bath System:

15L capacity with recirculation pump and protein skimmer

316L stainless steel construction with HEPA filtration

WearMaster Pro Software:

Automated wear rate calculation (mass loss/volume displacement)

21 CFR Part 11-compliant audit trail with blockchain timestamping

Remote monitoring via iOS/Android app

Operator Kit:

Calibrated torque wrench set (1–50 Nm)

Specimen alignment gauges (ISO 14242-1 compliant)

Calibration Bundle:

NIST-traceable force calibration weights

Angular encoder verification tool

Safety Kit:

Laser safety curtains

Acoustic enclosure with 30 dB noise reduction

Другие товары поставщика

	Enamel Boiling Water Mass Loss Tester	Product Introduction: The enamel layer boiling water weight loss tester is designed according to QB/T 2590-2003 Appendix A, GBT99892-2015 /ISO 287...
	Ross Flex Tester	Whole Sole ROSS Flexing Tester GT-KB05D To determine right angle flexing risistance for whole sole of rubber, PU, PVC, TPR foam and other materials...
	Mask Bacterial Filtration Efficiency meter	Medical Masks bacterial filtration efficiency tester also called BFE test machine is to determine the bacterial filtration efficiency (BFE) of medi...
	Sliding bearing PV friction testing machine	Standard This machine is mainly applicable to GB 7948-1987 plastic bearing limit PV test method, JB/T 7381-2010 powder metallurgy oil bearing PV v...
	Timken Bearing Friction and Wear Tester	Testing Standards ASTM D 2509 ASTM D 2782 GB/T3142 SH/T0204 Applicable standards Timken extreme pressure friction testing machines are usuall...

Все товары поставщика

Похожие товары

	Plastic Smoke Density Tester F313	Продавец: Standard International Group (HK) Limited	The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ...
	Xenon Test Chamber	Продавец: Standard International Group (HK) Limited	Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli...
	Single Cable Vertical Flame Tester	Продавец: Qinsun Instruments Co., LTD	Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ...
	Safety Helmet Flammability Tester	Продавец: Qinsun Instruments Co., LTD	Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda...
	Furniture flammability tester	Продавец: Qinsun Instruments Co., LTD	Product details Furniture flammability tester is mainly used to test the combustion performance ...