Wire and cable fire resistance testing machine
Meet the standard：
GB/T19216.11-2003/IEC60331-11:1999 "Under flame conditions of cable and optical cable line integrity test Part 11: test device-a flame temperature of not less than 750℃ for individual fire supply" design;
GB/T19216.21-2003/IEC60331-21.1999 "Line integrity test for cables and optical cables under flame conditions - Part 21: Test procedures and requirements - Cables with rated voltage 0.6/1.0KV and below" :GB/T19216.23-2003/IEC60331-23:19 99 "Line integrity test for cables and optical cables under flame conditions-Part 23: Test procedures and requirements-Data cables" :GB/T19216.25-2003/IEC60331-25:1999 "Line integrity test for cables and optical cables under flame conditions-Part 25: Test procedures and requirements-a cable" test standard; At the same time, it meets the standard of GB/T19666-2019 "General Rules for flame retardant and fire-resistant wire and cable"
Technical parameters:
Test station :1 station, one sample at a time.
Test product size: Length {>}1200mm. Length {>}1500mm.
The machine has a total of 5 wire support rings, the test sample will be placed on the wire support ring, and with two measuring fixtures. It is suitable for testing whether the cable or optical cable maintains the integrity of the line when feeding fire at a flame of not less than 750C.
Test wall: The wall is composed of heat-resistant, flame retardant material and is fixed on two horizontal steel beams, one at the upper part of the board and the other at the bottom of the board. The board is about 900mm long, 300mm wide and 9mm thick, and the total weight of the wall (that is, the board plus the supporting frame) is 10±2kg Each steel beam is a square steel pipe with a length of about 1m and 25mm.
If filling material is required, it needs to be placed inside the steel beam. The upper steel beam shall be fixed to the plate so that its upper surface is flush with the upper edge of the plate. The outer edge of each steel beam and plate has a horizontal hole, the exact position of which is determined by the requirements of the specific support liner and support frame.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Building Materials Non-combustibility Tester | Product details Building materials non-combustibility testeris designed to test the combustibility of main components in homogeneous and nonhomoge... |
 |
American European bending test meter | Test Purpose： To determine if metal wires in children's products bend or break under stress, creating sharp edges or points that pose choking or i... |
 |
Battery Adiabatic Calorimeter | Reference Standards GB/T 36276 - 2023 *Lithium - ion Batteries for Electric Power Energy Storage UL 9540A ASTM E1981 - 98(2012) SN/T 3078.1 - 201... |
 |
Cone Calorimeter | Ignition system 1、 10kV spark lighter with safe fire-off device. The lighter automatically detect its position via the lever which connects to the... |
 |
Abrasive Wear Testing Machine | Standard ASTM G65 - 04 GB/T 3960-1983 Main Purposes The wet - type rubber wheel abrasive wear testing machine is primarily employed to assess t... |
Похожие товары
 |
Plastic Smoke Density Tester F313 | Продавец: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | Продавец: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Продавец: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Продавец: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Продавец: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
