Wire and cable fire resistance testing machine
Meet the standard：
GB/T19216.11-2003/IEC60331-11:1999 "Under flame conditions of cable and optical cable line integrity test Part 11: test device-a flame temperature of not less than 750℃ for individual fire supply" design;
GB/T19216.21-2003/IEC60331-21.1999 "Line integrity test for cables and optical cables under flame conditions - Part 21: Test procedures and requirements - Cables with rated voltage 0.6/1.0KV and below" :GB/T19216.23-2003/IEC60331-23:19 99 "Line integrity test for cables and optical cables under flame conditions-Part 23: Test procedures and requirements-Data cables" :GB/T19216.25-2003/IEC60331-25:1999 "Line integrity test for cables and optical cables under flame conditions-Part 25: Test procedures and requirements-a cable" test standard; At the same time, it meets the standard of GB/T19666-2019 "General Rules for flame retardant and fire-resistant wire and cable"
Technical parameters:
Test station :1 station, one sample at a time.
Test product size: Length {>}1200mm. Length {>}1500mm.
The machine has a total of 5 wire support rings, the test sample will be placed on the wire support ring, and with two measuring fixtures. It is suitable for testing whether the cable or optical cable maintains the integrity of the line when feeding fire at a flame of not less than 750C.
Test wall: The wall is composed of heat-resistant, flame retardant material and is fixed on two horizontal steel beams, one at the upper part of the board and the other at the bottom of the board. The board is about 900mm long, 300mm wide and 9mm thick, and the total weight of the wall (that is, the board plus the supporting frame) is 10±2kg Each steel beam is a square steel pipe with a length of about 1m and 25mm.
If filling material is required, it needs to be placed inside the steel beam. The upper steel beam shall be fixed to the plate so that its upper surface is flush with the upper edge of the plate. The outer edge of each steel beam and plate has a horizontal hole, the exact position of which is determined by the requirements of the specific support liner and support frame.
在线联系供应商
Other supplier products
 |
Fiber Blend Ratio Tester | Product Introduction: It is used to measure the resistance value with a certain density under a certain geometry, and then converts it into the sp... |
 |
Geotextile equivalent aperture tester (wet sieve method) | Scope of application: The equivalent pore diameter of geotextile and its related products was determined by wet screen method. The geotextile samp... |
 |
Car seat foam performance tester | Applicable standards: GB/T 6670-2008"Determination of falling ball resilience of soft foam polymeric materials" : This standard specifies the test... |
 |
Ruhr conical joint multi-function tester | Product introduction It is mainly used to test the leakage, gas, separation force, unscrewing torque, easy assembly, resistance to slip wire, ... |
 |
Carpet Dimensional Stability Tester | Standard ASTM D5417(Standard Test Method for Assessing Carpet Dimensional Stability) ISO 2551(Textile Floor Coverings - Determination of Dimens... |
Same products
 |
Custom Stainless Components for OEM Applications | 卖方: Yongjia County Yaokang Technology Co., Ltd. | Our stainless steel float balls are designed for float valves, water tanks, and industrial liquid... |
 |
FH-77富氢测试笔 | 卖方: 科立龙电子股份有限公司 | 产品说明： 用于测量氢气水（富氢水）和氢气水发生器的溶解氢含量。 特征： 1、电极更换方便 智能、携带方便、操作方便、实用； 产品广泛应用于食品、环卫、地质勘探、冶金、地表水、 ... |
 |
Xenon Arc Weather Ometer | 卖方: Standard Group (Hong Kong) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | 卖方: Standard Group (Hong Kong) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | 卖方: Standard Group (Hong Kong) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
