Low-Temperature Bending Resistance Tester

• 

Applicable Standards

The tester adheres to international standards for material testing at low temperatures, including:

ISO 4674-2(Rubber- or plastics-coated fabrics – Determination of low-temperature bend test)

ASTM D1790(Standard test method for resistance of organic coatings to the effects of rapid deformation (impact))

GB/T 2423(China’s national standard for environmental testing – Cold tests)

EN 60068-2-1(Environmental testing – Cold tests for electronic components)

SAE J2339(Cold temperature impact resistance for automotive coatings)

These standards ensure consistent evaluation of material behavior under thermal and mechanical stress.

Working Principle

The tester operates bycombined thermal and mechanical stress:

Temperature Conditioning: Samples are cooled to -70°C in a climate chamber.

Bending Cycle: A motorized arm repeatedly bends the sample at a preset angle (e.g., 90° or 180°) and frequency (e.g., 100 cycles/min).

Cycle Execution: The test runs until surface cracks appear, or a predefined cycle count (e.g., 20.000 cycles) is reached.

Damage Assessment: Post-test, samples are evaluated for cracking, delamination, or coating failure using microscopy or visual grading.

Test Principle & Applications

Cold Flexibility Testing (ISO 4674-2/ASTM D1790):

Samples are bent 10.000–50.000 times at -40°C to simulate polar or alpine conditions.

Results are graded based on crack appearance:

Pass: No visible cracks or coating separation.

Fail: Cracks exceeding 0.5 mm in width.

Key Industries:

Aerospace: Validating aircraft fuel lines and sealants.

Automotive: Testing battery packs and exterior trim for electric vehicles.

Construction: Assessing pipe insulation and roofing membranes.

The Low-Temperature Bending Resistance Tester is indispensable for manufacturers developing products for extreme climates, ensuring reliability and compliance with regulatory standards. Its precision and adaptability make it a cornerstone of materials testing in harsh environments.

Main Parameters

Другие товары поставщика

	Vapor Shrinkage Tester	I. Product Overview TheVapor Shrinkage Testeris a specialized thermal analysis instrument designed to measure dimensional changes in textiles, pol...
	Textile Bonded Door Drench Tester	I. Product Overview TheTextile Bonded Door Drench Testeris a specialized instrument designed to evaluate the water resistance and durability of te...
	3D Rotary Cleaner	3D rotary high pressure cleaner for IBC totes This 3D rotary cleaner is suitable for cleaning of IBC totes. During the cleaning process, 3D rotar...
	Rain Tester	Standard AATCC 35: Water Resistance: Rain Test for Fabrics BS EN ISO 22958: Textiles – Determination of Resistance to Water Penetration &nd...
	Geosynthetic Clogging Tester	Scope of application: The method of gradient ratio is used to measure the permeability coefficient and permeability ratio of soil and geotextile s...

Похожие товары

	Seat Bumping and Creep Test Bench	Продавец: Standard International Group (HK) Limited	This test bench is used for simulating the car seat bumping and creep situation when a car is run...
	Automobile seat belt fixed point test bench	Продавец: Standard International Group (HK) Limited	Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur...
	Impact strength tester for car seat headrest	Продавец: Standard International Group (HK) Limited	Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi...
	Impact strength tester for car seat launching headrest	Продавец: Standard International Group (HK) Limited	Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w...
	Automobile Headrest Strength Tester	Продавец: Standard International Group (HK) Limited	Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me...