27dBm 2100MHz Signal Booster MGC AGC ALC
HPC-W27 3G WCDMA2100mhz Mobile Phone signal booster3G mobile networks are everywhere around the world but depending on where a mobile is located, regrettably the quality of the 3G signals differ significantly from excellent to poor. The item in auction is designed to address the signals strength issue by boosting the signals in two directions (Full Duplex) :1. Signals transmitted from a mobile are received by the signal booster over the air via the booster's indoor antenna and these signals are amplified and retransmitted over the air via the booster's outdoor antenna to a nearby cellular base station.2. Signals transmitted from a cellular base station are received over the air by the booster via the booster's outdoor antenna and these signals are amplified and retransmitted over the air via the booster's indoor antenna to a mobile .The 3G Booster can be viewed as an intermediate agent to help to set up a reliable wireless link between a mobile and the 3G mobile networks infrastructure.We provides signal boosters kits for any Homes, Offices, Cars, RV's, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more.HPC-W-27 WCDMA 3G 21mhz repeater Features:1.With unique appearance design, have good cooling function2.With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;3.With DL signal LED display, help to install the outdoor antenna at the best state;4.With AGC and ALC, make repeater work stable . 5.PCB with isolation function ,make UL and DL signal not influence each other,6.Low intermodulation, high Gain ,stable Output power HPC-W-27 2100mhz repeater Inside and Outside DesignHPC-W-27 Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better call quality and smoother data transmission. It is designed to support coverage area max can up to 2000 square meters with proper engineering. Below are the main features.1. The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.2. Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.3. To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.4. Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators. 5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.6.Multiple s and other handheld devices throughout a building can benefit from a wireless repeater.7.Supports up to (500) users / calls simultaneously.8.Extended battery life. (Your does not need to put out as much power due to improved reception.)Specification of HPC-W-27 Dual band repeater:Electrical specificationUplinkDownlinkFrequency RangeWCDMA 21001920 ~ 1980 MHz2110 ~ 2170 MHzMax .Gain≥ 75dB≥ 78dBMax .Output Power≥ 24dBm≥ 27dBmMGC ( Step Attenuation )≥ 31dB / 1dB stepAutomatic Level Control≥ 20dBGain FlatnessGSM & CDMATpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P)WCDMA≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P)Noise Figure≤ 5dBVSWR≤ 2.0Group Delay≤ 1.5μsFrequency stability≤ 0.01ppmSpurious Emission & Output inter-modulationGSM Meet ETSI TS 151 026 V 6.1.0WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )CDMA Meet IS95 & CDMA2000WCDMA SystemSpurious Emission MaskMeet 3GPP TS 25.143 ( V 6.2.0 )Modulation Accuracy≤ 12.5%Peak Code Domain Error≤ -35dB@Spreading Factor 256CDMA SystemRhoρ > 0.980ACPRMeet IS95 & CDMA2000Mechanical SpecificationsStandardI /O PortN-FemaleImpedance50 ohmOperating Temperature-25ºC~+55ºCEnvironment ConditionsIP40Dimensions155x112x85mmWeight≤ 1.50KgPower SupplyInput AC90-264V,output DC 5V / 3ALED AlarmStandardPower LEDPower IndicatorUL LEDBe lighted when there is callingDL 1Be lighted when Outdoor signal is -65dBDL 2Be lighted when Outdoor signal only -55dBDL 3Be lighted when Outdoor signal only -50dBThe installtion of the RepeaterOutdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal), (Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add more antenna,the HPC-W-27 Max can work with 10pcs indoor antenna. ( when add antenna ,please remember to take splitters )How should you install repeater (very easy and simple):Step 1: Use your mobile to test signal strength outside house or on roof, -70dbm is the basic requirement (full bar).Step 2 Install outdoor antenna in that location and keep adjusting, point it to signal tower station, try to get best signal.Step3: Run outdoor coaxial cable into building in a convenient location to connect with signal repeater.step 4: Mount your indoor antenna with signal repeaterstep5: Power up signal repeater device to check the signal inside, moving outdoor antenna until you get satisfied signal.Note: Connect outdoor (BTS) port with outdoor antenna, connect indoor ANT(MS) port with indoor antenna, outdoor antenna is mounted at a higher position. Both antennas should be 10 meters far away from each other at least.Indoor and outdoor antenna must be separated by wall.Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us.Terms and ConditionsCertificateCE/RoHsCountry of OriginChinaPort of DispatchShenzhenProduction Capacity1000pcs/monthDate of DeliveryWithin 3 days after received payment informMOQ10pcsWarranty2yearsPacakge1pcs/box; 20pcs/cartonCountry of OriginChina
Other supplier products
All supplier products
Same products
