Max Coverage 3500m2 GSM900 DCS1800 3G 2100 Tri band signal repeaters
HPC-GDW-27 GSM900 DCS1800 3G 2100 Tri band signal repeatersA cell signal booster (also known as cellular repeater or amplifier) is a device that boosts cell signals to and from your mobile whether at home or office or in any vehicle. It does this by taking the existing cellular signal, amplifying it, and then broadcasting to an area in need of better reception.If you're experiencing dropped calls, slow or lost internet connection, stuck text messages, poor voice quality, weak coverage, low bars, and other cell reception problems, a cell signal booster is the best solution that produces definite results.We provides signal boosters kits for any Homes, Offices, Cars, RV's, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more.HPC-GDW-27 Tri band repeater Features:1.With unique appearance design, have good cooling function2.With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;3.With DL signal LED display, help to install the outdoor antenna at the best state;4.With AGC and ALC, make repeater work stable . 5.PCB with isolation function ,make UL and DL signal not influence each other,6.Low intermodulation, high Gain ,stable Output power HPC-GDW-27 repeater Inside and Outside DesignHPC-CP-27 Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better call quality and smoother data transmission. It is designed to support coverage area max can up to 2000 square meters with proper engineering. Below are the main features.1.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.2.Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.3.To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.4.Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators. 5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.6.Multiple s and other handheld devices throughout a building can benefit from a wireless repeater.7.Supports up to (500) users / calls simultaneously.8.Extended battery life. (Your does not need to put out as much power due to improved reception.)Specification of HPC-GDW-27 Tri band repeater: Electrical specification UplinkDownlinkFrequency RangeGSM900890 ~ 915 MHz935 ~ 960 MHzDCS1710 ~ 1785 MHz1805 ~ 1880 MHzWCDMA1920-1980MHz2110-2170MHzMax .Gain≥ 70dB≥ 75dBMax .Output Power≥ 24dBm≥ 27dBmMGC ( Step Attenuation )≥ 31dB / 1dB stepAutomatic Level Control ≥ 20dBGain FlatnessGSM & CDMATpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P)WCDMA≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P)Noise Figure≤ 5dBVSWR≤ 2.0Group Delay≤ 1.5μsFrequency stability≤ 0.01ppmSpurious Emission &Output inter-modulationGSM Meet ETSI TS 151 026 V 6.1.0WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )CDMA Meet IS95 & CDMA2000WCDMA SystemSpurious Emission MaskMeet 3GPP TS 25.143 ( V 6.2.0 )Modulation Accuracy≤ 12.5%Peak Code Domain Error≤ -35dB@Spreading Factor 256CDMA SystemRhoρ > 0.980ACPRMeet IS95 & CDMA2000Mechanical SpecificationsStandardI /O PortN-FemaleImpedance50 ohmOperating Temperature-25oC~+55oCEnvironment ConditionsIP40Dimensions220x320x40mmWeight≤ 3.50KgPower SupplyInput AC90-264V,output DC 5V / 6ALED AlarmStandardPower LEDPower IndicatorUL LEDBe lighted when there is callingDL 1Be lighted when Outdoor signal is -65dBDL 2Be lighted when Outdoor signal only -55dBDL 3Be lighted when Outdoor signal only -50dB The installtion of the RepeaterOutdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal), (Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add more antenna,the HPC-GW-27 Max can work with 10pcs indoor antenna. ( when add antenna ,please remember to take splitters )Installation steps Step 1 Start by taking your up to the roof or other location outside to find where the signal is strongest.Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the Signal Repeater.Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us.
Other supplier products
All supplier products
Same products
