Busbar Insulation Coating
The silicone rubber insulation coating is made from special silicone rubber, high-performance material and other polymers by polymer blending technology. Its basic structural unit is silicon - oxygen chain while its side chain is connected by silicone with another organic radical group. Therefore, this structure makes the coating well combine the properties of both organic and inorganic compound. This product can used for the equipment and components which need protection of insulation, thermos conduction, fire retardant, dampness-proof, etc., such as bare wire, busbar, cable, high-power generator, dry-type reactor, dry-type transformer, switch cabinet and so on, it's quite suitable for the electrical equipment which operated in contaminated and humid environments.
Product Standard of busbar insulation coating:
DL/T 627-2012 Room Temperature Vulcanized Silicone Rubber Anti-Pollution Coating for Insulators
IEEE 1523 IEEE Guide for Application, Maintenance, and Evaluation of Room Temperature Vulcanized (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators
Contact us get more details about RTV-II Silicone Rubber Coating, such as TDS, Application Method, OEM etc.
Product Features of Busbar Insulation Coating:
Product Standard of Busbar Insulation Coating:
DL/T 627-2012 Room Temperature Vulcanized Silicone Rubber Anti-Pollution Coating for Insulators
IEEE 1523 IEEE Guide for Application, Maintenance, and Evaluation of Room Temperature Vulcanized (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators
Contact us get more details about RTV-II Silicone Rubber Coating, such as TDS, Application Method, OEM etc.
|
Item |
Silicone Rubber Insulation Coating |
Heat Shrink Tube |
|
Electrical Insulation |
Excellent electrical insulation. Breakdown Voltage is more than 25 kV/mm. |
Common performance. |
|
Cover Effect |
Excellent adhesion.The coating layer is intense, it could strongly stick to the equipment surface and could well resist to the corrosion caused by acid, alkali, salt and air. |
Common cover effect especially in the connection part. |
|
Thermal Conductivity |
The coating has closely attached to the conductor and has good thermal conductivity could better release the heat of equipment. Its thermal conductivity is 0.2W/ (m. k), which is ten times then air. |
Relatively poor due to there is air gap between the tube and equipment. |
|
Flame Retardant |
Hard to burn and has good fire retarding ability up to FV-0 Class. |
Easy to deform, crack and broke. |
|
Application |
Favorable hardness makes its construction time is short. (less than one working day)It can well fit and protect the surface of special shaped equipment or components and special connection position so that to make the conductors as one. |
Long construction time and need to disassemble the equipment.It’s easy to crack and broken for the coating on the special shaped equipment or components and the connection or twist place. |
|
Maintenance |
Easy to maintain and repair. The coating will not affect the dismounting of screw or bolt. Moreover, if recoating, the new coating can have integrated fuse with the old coating tightly. |
Although it’s also convenient to maintain and repair, but the connection place is easy to peel and broke. |
|
Ageing Resistance |
Good hydrophobicity and resistance to ageing, dampness, ozone, radiation, UV, etc. make it free of maintenance and can serve for a long time. Its service life could be more than 20 years. |
Poor ageing resistance, its service time is about 5 years or even less especially in some bad environment the cracking and break phenomenon will happen. |
|
Economic |
Excellent performance at reasonable cost. |
Lower cost. |
Send product request
Other supplier products
 |
Busbar Insulation Coating | The silicone rubber insulation coating is made from special silicone rubber, high-performance material and other polymers by polymer blending techn... |
 |
Enhanced Anti-pollution Flashover Coating RTV-II | A functional insulator coating to protect insulators in pollution area, such as industrial area, coastal area and other extreme environmental condi... |
 |
Line Post Insulator | We can offer different Voltage of Line Post Type Insulatorfor Transmission Line. Such as Long Rod Insulator, Rod Insulator and Pin Type Insulator. ... |
 |
Station Post Insulator | We offer different kinds of Station Post Insulator for Substation, such as Circuit Breaker (CB), Post Insulator, Disconnector, Potential Transforme... |
 |
Hollow & Bushing Insulator | We offer different kinds of Hollow & Bushing Insulator for Substation, such as Circuit Breaker (CB), GIS, Post Insulator, Disconnector, Potenti... |
Same products
 |
Cylindrical Block Graphite Heat Exchanger | Seller: Sunshine Graphite | Advantages: High structural strengthGood resistance to impactHigh volume-utilization rateHigh he... |
|
|
Station Post Insulator | Seller: Fujian Ruisen New Materials Co., Ltd. | We offer different kinds of Station Post Insulator for Substation, such as Circuit Breaker (CB), ... |
 |
Slot Button Type Silicone Rubber Busbar Joint Box | Seller: Fujian Ruisen New Materials Co., Ltd. | The electrical junction box with busbaris a new type bus bar insulation cover, it is fabricated w... |
 |
Silicone Rubber Insulation Product | Seller: Fujian Ruisen New Materials Co., Ltd. | The Characteristics of silicone electrical insulationProduct Since silicone rubber has high bond... |
 |
RTV High Voltage Insulator Coating | Seller: Fujian Ruisen New Materials Co., Ltd. | Anti-pollution Flashover Coating (rtv insulator coating) High Voltage Insulator Coatings (HVIC) ... |
