JMZ-T Rubber & Metal Anti Vibration Mount

• 
• 
• 

The JMZ-T series anti vibration mount is the new designed model, which is designed especially for the military use. Comparing with the wire rope isolators, this model is small and tinny, which has no worrying about the space limits.

The max static load of the JMZ-T Series anti vibration mount is from 1.4kg to 2.8kg, which can be specially used in many precision equipment and system in helicopter, motor, embedded electronics, etc.

The JMZ-T Series can also be used in the very narrow spaces to meet the mountable environmental requirements. This new type friction damper is the very selection for the limits of the space under some special situations.

An earthquake is caused by the motion of the ground which causes the forced vibration of a building that is still at rest on the ground, resulting in internal forces, deformation and displacement in the structure. is an isolated earthquake, To isolate or dissipate vibration energy by setting a control mechanism at the base or at a certain location of buildings and structures to avoid or reduce the transmission of vibration energy to the upper structure, reduced the vibration response of the structure, so that only minor motion and deformation of the building can be realized during the earthquake to ensure the safety of buildings. In isolation technology, foundation isolation technology is a hot new technology in the world. The base isolation technology is widely used, it is especially suitable for medium-and low-rise brick-concrete buildings and reinforced concrete buildings.

What is the basic vibration isolation technology

Traditional vibration isolation structure mainly utilizes plastic deformation and energy dissipation of the main structure to dissipate vibration energy after yielding，therefore, the performance requirements of these regions are particularly important. Once these areas have problems due to certain factors, it will affect the vibration resistance of the structure seriously, even produce serious damage. And the foundation isolation is to set a layer of isolation with sufficient reliability between the superstructure of the building and the top of the foundation to separate the superstructure from the foundation, and blocks the propagation of vibration waves to the superstructure, so that the vibration energy of the input structure is absorbed by the energy dissipation elements of the isolation layer, therefore, it will reduce the vibration response of the superstructure greatly, so that ensure the safety of the building.

The basic principle of base isolation technology

According to the experiment, if the period of the structure is prolonged and a large damping is given, it will greatly reduce the acceleration response on the structure. At the same time, large displacements to the structure can be provided by an isolation layer between the bottom of the upper structure and the top of the foundation. In this way, the superstructure will move close to translation during the earthquake, so the safety degree of the superstructure is greatly improved, which is the principle of base isolation. It is shown in the curve of the structural reaction spectrum below. From the acceleration response spectrum of figure (a), we can see that the acceleration response of the structure decreases with the prolongation of the period, so that the inertia force acting on the structure is reduced; but from the displacement response spectrum of (b), the period is prolonged and the displacement response is increased. If a damping device is introduced into the structure, the displacement response of the structure can be reduced, and the corresponding acceleration response can also be reduced.

Other supplier products

	GRY-10A Stainless Steel Camera Vibration Isolator for UAV/Camera/Gimbal Shock Absorption	The GRY-10A marine shipbuilding vibration mount is made by the 30 loops 1.5mm diameter wire rope winded in the two mounting bars. The max static lo...
	JMZ-1-1.5B Rubber Anti Vibration And Shock Absorbing Mounts	JMZ-1-1.5Ashock isolation mountbelongs to the JMZ-1 series. It adopts the structure of double spring and special friction plate. It has good impact...
	JGX-1278 Wire Rope Elastomeric Vibration Isolators/Mounts For Multi Application	JGX-1278 multi-application elastomeric isolation mounts/wire rope isolatoris the 8 loops 12.7mm diameter model with max static load from 122kg to 3...
	GRY-100A Stainless Steel Vibration Mount for Industrial Shipbuilding/Camera/Cinema Shock Vibration	The GRY-100A marine shipbuilding vibration mount is made by the 30 loops 2.4mm diameter wire rope winded in the two mounting bars. The max static l...
	Analysis of Advantages and Disadvantages of Rubber Shock Absorber	Advantages of rubber: Comparing with metal spring spring shock absorber, it can determine shape freely and control hardness by adjusting rubber com...

Same products

	Multi-Application Wire Rope Vibration Isolator	Seller: Xi\'an Hoan Microwave Co., ltd	Among all of wire rope isolator manufacturers, Hoan is proud to release multi-application wire ro...
	Military Wire Rope Vibration Isolator	Seller: Xi\'an Hoan Microwave Co., ltd	This defensemotor vibration isolatorswire isolator are now widely used in the field of military v...
	Marine Wire Rope Vibration Mounts	Seller: Xi\'an Hoan Microwave Co., ltd	Advantages of Marine Wire Rope Vibration Mounts (GRY Series) Anti vibration camera mountsare com...
	JGX-1598 Wire Rope Vibrationsisolator/Shock Isolator For Multi Application	Seller: Xi\'an Hoan Microwave Co., ltd	Vibrationsisolatorer Wire rope isolators are also called wire rope anti vibration mounts, which ...
	JGX-1278 Wire Rope Elastomeric Vibration Isolators/Mounts For Multi Application	Seller: Xi\'an Hoan Microwave Co., ltd	JGX-1278 multi-application elastomeric isolation mounts/wire rope isolator is the 8 loops 12.7mm ...