.

Motor Driver For Nema 2M423A

2M432ACharacteristic :1.Using new  digital sinusoidal micro-segmentation algorithm 2.Lower  heating and noise ,Website:, higher stability 3.The phase  current can be adjusted by switch DIP.4.For the  input control signal, electric circuit use optically coupled isolator to low  the noise interference .5.With short  circuit, overvoltage, undervoltage, overtemperature protection and improving  functionsstepper Motor driver Specification :Input    Power supply :12-40VDCOutput    Current0.4A~3.2ADrive    WayPWM constant    current chopping ,two phase Sine wave output currentSuitable    stepper motor35,42,57    series two phase stepper motorAmbient    environment-10℃~55℃    15~85%RH、No condensation. Non-corrosive, flammable, explosive,    conductive gas, liquid and dustKeeping    enviroment-40℃~+55℃, <93%RH,No condensation, no frostSize    (L*W*H)115*68*24mmNet Weight0.25 KgCurent seting :SW1-SWPhase current0.4A0.8A1.2A1.6A2.0A2.4A2.8A3.2AMicrostep Subdivision setting :     SW1-SWsteps/revDescribtion :Microstep    setting    Users can set the driver Microstep by the    SW1-SW5 five switches,total 28 micro-step. When you set the    microstep , pls stop the driver working.The    setting of the specific Microstep subdivision, please refer to the    instructions of the driver panel figure .Output    current setting  Users can set the driver Microstep by the    SW1-SW5 five switches. The setting of the specific Microstep subdivision,    please refer to the instructions of the driver panel figure..Double    pulse setting    SW7 sets pulse mode, setting “on''    as double pulse mode, setting “off'' as pulse + direction mode.,CW+/CW is Clockwise ,CCW+/CCW-  is Counterclockwise , need to confirm the    wire of stepper motor .Automatic    half current function    Users can set the driver half flow    function by SW6. "OFF" indicates the quiescent current is set to    half of the dynamic current, that is to say, 0.5 seconds after the cessation    of the pulse, current reduce to about half automatically. "ON"    indicates the quiescent current and the dynamic current are the same. User    can set SW6 to "OFF", in order to reduce motor and driver heating    and improve reliability.Self    test function   When SW1-SW5 is OFF , Inner of drive send 1K    pulse to test whether the motor,wire,and self is normal.signal    Interface  PUL+ and PUL- are the positive and negative    side of control pulse signal; DIR+ and DIR- are the positive and negative    side of direction signal; ENA+ and ENA- are the positive and negative side of    enable signal .Motor    Interface   A+ and A- are connected to a phase winding    of motor; B+ and B- are connected to another phase winding of motor. If you    need to backward, one of the phase windings can be reversed .Power    Interface    It    uses DC power supply,recommended working voltage is 12-40VDC,power is over 50W,voltage shouldn’t    be over 40VDC and  below 12VDC.Indicator    Lightor  There are two indicator lights. Power    indicator is green. When the driver power on, the green light will always be    lit. Fault indicator is red, when there is over-voltage or over-current    fault, the red light will always be lit; after the driver fault is cleared,    if re-power the red light will be off..Installation  The size of motor driver is 115×68×24 mm,mounting holes is 100mm.Chest and upright installation are ok,we suggest upright installation. During installation, it should be close to the metal    cabinet for heat dissipation.signal interface and sequence in time : Inner electric circuit of motor drive :  Interface connection and installing size : 


Send product request

To: Changzhou Weitong Electromechanical Manufacturing Co., Ltd.
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

Motor Driver For Nema 2M423A
Motor Driver For Nema 2M423A 2M432ACharacteristic :1.Using new  digital sinusoidal micro-segmentation algorithm 2.Lower  heating and noise ,Website:, higher stability 3.The pha...
1.2 Degree Nema 52 Stepper Motor 1303P
1.2 Degree Nema 52 Stepper Motor 1303P Nema 52 three  phase stepper motor  Technique  Parameters  ItemsSpecifictionStep Angel1.2 degreeStep Angel Accuracy±5%Resistance Accuracy±10%Induct...
AC Stepper Motor Driver 2H8006T
AC Stepper Motor Driver 2H8006T Characteristic :1.Using new digital sinusoidal micro-segmentation algorithm 2.Support single / dual control pulse input 3.A test run function,Websi...
All supplier products

Same products

 LA22.5E 200 24VDC Spindle Motor For Spreader XLS50
LA22.5E 200 24VDC Spindle Motor For Spreader XLS50 Seller: DONGGUAN FAVORABLE AUTOMATION EQUIPMENT CO.,LTD Welcome to find the high quality la22.5e 200 24vdc spindle motor for spreader xls50 at the offic...
 LA30 1S-200 24VDC SPINDLE MOTOR
LA30 1S-200 24VDC SPINDLE MOTOR Seller: DONGGUAN FAVORABLE AUTOMATION EQUIPMENT CO.,LTD Welcome to find the high quality la30 1s-200 24vdc spindle motor at the official online store of...
 Series 3 103658/FC 24V D.C Gearmotor
Series 3 103658/FC 24V D.C Gearmotor Seller: DONGGUAN FAVORABLE AUTOMATION EQUIPMENT CO.,LTD Welcome to find the high quality series 3 103658/fc 24v d.c gearmotor at the official online sto...
 Replace Kit For Gearmotor
Replace Kit For Gearmotor Seller: DONGGUAN FAVORABLE AUTOMATION EQUIPMENT CO.,LTD Welcome to find the high quality replace kit for gearmotor at the official online store of Favo...
 Replaced By
Replaced By Seller: DONGGUAN FAVORABLE AUTOMATION EQUIPMENT CO.,LTD Welcome to find the high quality replaced by at the official online store of Favorable Automati...