Thermal Protective Performance Tester (TPP)

• 

The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.

Standards：

BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306

Feature：

Industrial personal computer with analysis software is suitable for severe testing conditions.

Automatic calculation for heat transmission factor and radiant heat transfer index.

Sample holder with force applied kit is easy to operate.

Single pump for shutter movement and cooling water loop.

Parameter：

• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size

• Copper slug calorimeter sensors (ASTM or ISO)

• ± 0.75°C temperature measurement

• ± 3% radiant heat flux measurement

• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)

• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)

• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase

• Maximum nominal current 20 Amps

• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)

• Cooling Water: Cooling water required, chiller or tap water source is acceptable

• Propane Requirement: Regulated supply at 15 PSI (minimum)

• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps

• Two gas burners with flame detection auto ignition

• Mass flow controller for precise gas control

• Water-cooled protective shutter

• Pneumatic sample carriage and shutter assembly

• Integrated sensor cooling stand (air cooled)

• Emergency stop cuts gas flow, power to lamps and pneumatics

• Tinted tempered glass shield protects operator

• Software safety interlocks monitor water flow, carriage position, burner ignition

Другие товары поставщика

	Jet wash water tank cleaning machine	Tank cleaning machine High impact 3D rotary tank washer Model number: DG8 jet wash water tank cleaning machine Working Principle: Impeller is d...
	Limiting Oxygen Index Tester	Limiting Oxygen Index Tester The oxygen index of the material refers to the minimum oxygen concentration that can maintain the combustion of the ma...
	Impact strength tester for car seat headrest	Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requirements and test methods" : This standard specifie...
	Water Vapour Permeability Tester	Information The device is a constant temperature and humidity moisture permeability test device, which is suitable for sportswear and other requ...
	Automotive Seat Belt Buckle Bending Test Machine-QINSUN	Standard ISO 10195(Seat Belt Anchorage Hardware - Test Methods) ECE R16(Uniform Provisions Concerning the Approval of Safety Belts and Restrain...

Похожие товары

	Air Intake Filter Test System	Продавец: Standard Groups	The Air Intake Filter Test System is designed for testing industrial air filters and engine air f...
	Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging	Продавец: Standard International Group (HK) Limited	The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f...
	Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester	Продавец: Standard International Group (HK) Limited	The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter...
	HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ...
	VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine	Продавец: Standard International Group (HK) Limited	The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia...